Decided to sell her again. To keep the thread clean please refrain from comments, opinions, etc... Weekly bump is fine. If you have any questions please call/text 8am-8pm CST at (4six9) five2zero - zero1zero3. Description, photos and video below. Thanks for looking! 😀
If you are reading this, yes the CAR IS STILL AVAILABLE. Cash or Bitcoin. No trades.
FOR SALE 1988 Fiero GT heavily modified
-5 Speed MANUAL transmission (not auto) -Vin 1G2PG1194JP215424 -Odometer mileage 142,512 -3.8L series II Super Charged Engine -Magnecor R-100 10mm Pure Silicone Racing Wires -Custom Ceramic Coated Headers (West Coast Fiero) -Borla Stainless Steel Exhaust (sounds mean but is not too loud at all) -High Flow Cat Converter -Height Adjustable Rear Koni Coil-Over adjustable struts with 325# Springs (Held Motorsports) -Height Adjustable Custom Front Carrera Coil-Over shocks with 7” 300# Springs (RCC specialties) -wheel bearings on all 4 wheels (Rodney Dickman) -Upper and Lower Ball Joints -rack and pinion bushing and bearing (Rodney Dickman) -All New Steering tie Rods (inner and outer) -Professional Powder coating of all suspension components, roll bars, engine cradle, and front brakes -Complete Urethane Bushings of all suspension Components and transmission mounts (rubber engine mount used to help reduce vibration rather than all urethane) -Transmission Bearings, Inside and Out -Centerforce Clutch -Phantom Grip Limited Slip Differential (works great- much better grip from both tires- unlike stock) -Cold Air Intake with K&N Air Filter -Stock Corvette Fuel Pump -Stainless Steel Braided Brake Lines (Fiero Store) -Custom Engine Bay Heat Shielding -Complete Dynamat under carpet of drivers side compartment and door -GT-One Honda NSX headlights
-IMSA front wide body Kit -Mad Curls rear wide body Kit
-Wheel Spacers (pair for rear wheels and made in USA) 6061-T6 Aluminum Alloy Construction 3/4" (19.05mm) thick. 5x100/57.1mm center to 5x114.3/73.1 mm center. Hubcentric on both sides.
-5 Speed Getrag Transmission -Choptop -Mazda RX8 mirrors -C4 Rotor Adapters (on all four wheels) for OEM Fiero calipers -Corvette C4 Slotted rotors -Leather MOMO Competizione steering wheel w/ NRG quick release hub -Front battery relocation tray -Rust free -Car is running. -AC need recharge. -New Alternator, belt and pulley. (9/8/20) -New fuel pump (9/8/20) -New Fuel filter (9/8/20) Asking $15,000 (USD) will accept Bitcoin (BTC) too. Car located in Alachua, FL (North Gainesville)
I live out of state. Fiero is stored at a family members barn. Build status: exterior body is over 90% complete and in primer. I've spent over $40k on this project car and don't have the time or interest to complete. She needs to go to a good home. More photos upon request. No rush in selling.
Decided to sell her again. To keep the thread clean please refrain from comments, opinions, etc... Weekly bump is fine. If you have any questions please call/text 8am-8pm CST at (4six9) five2zero - zero1zero3. Description, photos and video below. Thanks for looking! 😀
If you are reading this, yes the CAR IS STILL AVAILABLE. Cash or Bitcoin. No trades.
FOR SALE 1988 Fiero GT heavily modified
-5 Speed MANUAL transmission (not auto) -Vin 1G2PG1194JP215424 -Odometer mileage 142,512 -3.8L series II Super Charged Engine -Magnecor R-100 10mm Pure Silicone Racing Wires -Custom Ceramic Coated Headers (West Coast Fiero) -Borla Stainless Steel Exhaust (sounds mean but is not too loud at all) -High Flow Cat Converter -Height Adjustable Rear Koni Coil-Over adjustable struts with 325# Springs (Held Motorsports) -Height Adjustable Custom Front Carrera Coil-Over shocks with 7” 300# Springs (RCC specialties) -wheel bearings on all 4 wheels (Rodney Dickman) -Upper and Lower Ball Joints -rack and pinion bushing and bearing (Rodney Dickman) -All New Steering tie Rods (inner and outer) -Professional Powder coating of all suspension components, roll bars, engine cradle, and front brakes -Complete Urethane Bushings of all suspension Components and transmission mounts (rubber engine mount used to help reduce vibration rather than all urethane) -Transmission Bearings, Inside and Out -Centerforce Clutch -Phantom Grip Limited Slip Differential (works great- much better grip from both tires- unlike stock) -Cold Air Intake with K&N Air Filter -Stock Corvette Fuel Pump -Stainless Steel Braided Brake Lines (Fiero Store) -Custom Engine Bay Heat Shielding -Complete Dynamat under carpet of drivers side compartment and door -GT-One Honda NSX headlights
-IMSA front wide body Kit -Mad Curls rear wide body Kit
-Wheel Spacers (pair for rear wheels and made in USA) 6061-T6 Aluminum Alloy Construction 3/4" (19.05mm) thick. 5x100/57.1mm center to 5x114.3/73.1 mm center. Hubcentric on both sides.
-5 Speed Getrag Transmission -Choptop -Mazda RX8 mirrors -C4 Rotor Adapters (on all four wheels) for OEM Fiero calipers -Corvette C4 Slotted rotors -Leather MOMO Competizione steering wheel w/ NRG quick release hub -Front battery relocation tray -Rust free -Car is running. -AC need recharge. -New Alternator, belt and pulley. (9/8/20) -New fuel pump (9/8/20) -New Fuel filter (9/8/20) Asking $15,000 (USD) OBO will accept crypto currency too. Car located in Alachua, FL (North Gainesville)
I live out of state. Fiero is stored at a family members barn. Build status: exterior body is over 90% complete and in primer. I've spent over $40k on this project car and don't have the time or interest to complete. She needs to go to a good home. More photos upon request see link below. No rush in selling.
No worries, never considered it a serious offer and I actually forgot about it.
quote
Originally posted by Notorio: Oh no! Sorry to see your sale fell through.
Thanks for your input. You mean 240p but I actually think it’s 144p. Best to look at pictures. She’s out of state. Next time when I’m in Florida I’ll get a 1080p or 4k video.
quote
Originally posted by reinhart: For an asking price of $15K you might want to post videos that are of higher quality than 240k
[This message has been edited by FierociousGT (edited 06-06-2021).]