Pennock's Fiero Forum
  The Mall
  85 GT V6 Top Engine Mount

Post New Topic  Post A Reply
Email This Page to Someone! | Printable Version


next newest topic | next oldest topic
85 GT V6 Top Engine Mount by Bakeys
Started on: 10-12-2014 07:06 PM
Replies: 6 (118 views)
Last post by: Bakeys on 10-13-2014 06:03 AM
Bakeys
Member
Posts: 53
From: Finger Lakes region, NY, US of A
Registered: Oct 2014


Feedback score: N/A
Leave feedback

Rate this member

Report this Post10-12-2014 07:06 PM Click Here to See the Profile for BakeysClick Here to Email BakeysSend a Private Message to BakeysEdit/Delete MessageReply w/QuoteDirect Link to This Post
Not sure why, but it seems like I'm searching for what may be the Holy Grail of parts.

There is an engine mount that connects to my cylinder head (rear) and more or less elbows back to the rubber-bushed torque link mount. ( I think.)

Well, where it bolts to the head, the mount is broken. Based on how the mounting hole was rounded out, it appears this little gazokka has been undergoing a fair amount of stress. I welded it to a standard that I thought was better than new, and within a week or so, it broke again.

So WHERE do I get one? Or, better yet, where do I get a GOOD one? Local scrap yard has 3 Fieros and only one is the V6 with the engine mount in question. But it's nearly as bad as mine.

Thanks all.
Lookin forward to pickin some brains in the future.

------------------
Bakeys

IP: Logged
PFF
System Bot
hookdonspeed
Member
Posts: 7980
From: baltimore, md
Registered: May 2008


Feedback score:    (9)
Leave feedback





Total ratings: 131
Rate this member

Report this Post10-12-2014 07:49 PM Click Here to See the Profile for hookdonspeedClick Here to visit hookdonspeed's HomePageClick Here to Email hookdonspeedSend a Private Message to hookdonspeedEdit/Delete MessageReply w/QuoteDirect Link to This Post
looking for the mount itself? http://rodneydickman.com/ca...th=22&products_id=72
best one you can get right there...
if your looking for the bracket, then im sure one of the members here has one.
IP: Logged
Bakeys
Member
Posts: 53
From: Finger Lakes region, NY, US of A
Registered: Oct 2014


Feedback score: N/A
Leave feedback

Rate this member

Report this Post10-12-2014 08:16 PM Click Here to See the Profile for BakeysClick Here to Email BakeysSend a Private Message to BakeysEdit/Delete MessageReply w/QuoteDirect Link to This Post
Nope.
That's the torque link.
Close.
But I'm looking for the steel bracket that link attaches to.
It goes from the torque link to the cylinder head bolt.

Try this: Mount is attached to torque link and turns left (just above the plug cap in this image.)

[This message has been edited by Bakeys (edited 10-12-2014).]

IP: Logged
Grantman
Member
Posts: 1418
From: Brownton, Minnesota, USA
Registered: Dec 2011


Feedback score:    (22)
Leave feedback

Rate this member

Report this Post10-12-2014 08:26 PM Click Here to See the Profile for GrantmanClick Here to Email GrantmanSend a Private Message to GrantmanEdit/Delete MessageReply w/QuoteDirect Link to This Post
might have one in storage, would need to stop there and check.
IP: Logged
Boostdreamer
Member
Posts: 7175
From: Kingsport, Tennessee USA
Registered: Jun 2007


Feedback score:    (24)
Leave feedback





Total ratings: 98
Rate this member

Report this Post10-12-2014 08:41 PM Click Here to See the Profile for BoostdreamerClick Here to Email BoostdreamerSend a Private Message to BoostdreamerEdit/Delete MessageReply w/QuoteDirect Link to This Post
I have one. PM sent.
IP: Logged
DKcustoms
Member
Posts: 1071
From: Central NY
Registered: Oct 2013


Feedback score:    (15)
Leave feedback

Rate this member

Report this Post10-12-2014 09:01 PM Click Here to See the Profile for DKcustomsSend a Private Message to DKcustomsEdit/Delete MessageReply w/QuoteDirect Link to This Post
I have one as well, located a little north of syracuse.

Let me know if you need it
IP: Logged
Bakeys
Member
Posts: 53
From: Finger Lakes region, NY, US of A
Registered: Oct 2014


Feedback score: N/A
Leave feedback

Rate this member

Report this Post10-13-2014 06:03 AM Click Here to See the Profile for BakeysClick Here to Email BakeysSend a Private Message to BakeysEdit/Delete MessageReply w/QuoteDirect Link to This Post
Thanks for the offers all.
The short answer is YES, I'm interested.
But I'd really like to see what you have first.

Am I the only one with this issue?

Seems every link mount I've seen is experiencing the same wear.

Thanks.
IP: Logged

next newest topic | next oldest topic

All times are ET (US)

Post New Topic  Post A Reply
Hop to:

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery | Ogre's Cave
Real-Time Chat | Fiero Related Auctions on eBay



Copyright (c) 1999, C. Pennock