Pennock's Fiero Forum
  General Fiero Chat - Archive
  my custom dash i am creating

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Email This Page to Someone! | Printable Version


my custom dash i am creating by bsculptor
Started on: 05-10-2004 08:49 PM
Replies: 8
Last post by: Borgio on 05-11-2004 02:27 AM
bsculptor
Member
Posts: 329
From: san diego
Registered: Jan 2004


Feedback score: N/A
Leave feedback

Rate this member

Report this Post05-10-2004 08:49 PM Click Here to See the Profile for bsculptorSend a Private Message to bsculptorDirect Link to This Post
heres my dash i am creating. I had bought this euro dash on ebay .. when i got it , it fit like crap. So i cut it
in half ... and attached it to the stock dash. I am rerouting the vents as the fiberglass sticks out some (stock fiero has alot of room anyhow)
i am just getting to the center console , trying to figure it out .



IP: Logged
PFF
System Bot
JKFIERO
Member
Posts: 2588
From: DuBois, PA
Registered: Oct 2002


Feedback score: N/A
Leave feedback





Total ratings: 92
Rate this member

Report this Post05-10-2004 08:54 PM Click Here to See the Profile for JKFIEROSend a Private Message to JKFIERODirect Link to This Post
Car LOOKS SHARP !!!

Will the new dash stick out much farther than the stock. I know I have busted off my corners several times.

IP: Logged
MooCow
Member
Posts: 2263
From: Charlotte, NC
Registered: Sep 1999


Feedback score:    (22)
Leave feedback

Rate this member

Report this Post05-10-2004 09:22 PM Click Here to See the Profile for MooCowSend a Private Message to MooCowDirect Link to This Post
Wow that looks great thus far. Just a question thoe, what do you plan to do with the part right above the stock guages? It looks like a big opening up there. Other than that it looks sweet so far. I can't wait until I start mine soon.

Thanks Ken

IP: Logged
bsculptor
Member
Posts: 329
From: san diego
Registered: Jan 2004


Feedback score: N/A
Leave feedback

Rate this member

Report this Post05-10-2004 09:31 PM Click Here to See the Profile for bsculptorSend a Private Message to bsculptorDirect Link to This Post
the gagues are not bolted in .. so its actually up about an inch or two. There will be a plexiglass covering
that whole part .. and blacked out where no gauges or lights are .


 
quote
Originally posted by MooCow:

Wow that looks great thus far. Just a question thoe, what do you plan to do with the part right above the stock guages? It looks like a big opening up there. Other than that it looks sweet so far. I can't wait until I start mine soon.

Thanks Ken


IP: Logged
Borgio
Member
Posts: 221
From: Kokomo, Indiana, USA
Registered: Oct 2001


Feedback score: N/A
Leave feedback

Rate this member

Report this Post05-10-2004 09:44 PM Click Here to See the Profile for BorgioSend a Private Message to BorgioDirect Link to This Post
How are you going to open the doors? It looks like the dash is in the way.
IP: Logged
bsculptor
Member
Posts: 329
From: san diego
Registered: Jan 2004


Feedback score: N/A
Leave feedback

Rate this member

Report this Post05-10-2004 09:56 PM Click Here to See the Profile for bsculptorSend a Private Message to bsculptorDirect Link to This Post
shhhh ... dont say that out loud.
im going to have to redo that also . still thinking ...

 
quote
Originally posted by Borgio:

How are you going to open the doors? It looks like the dash is in the way.

IP: Logged
jscott1
Member
Posts: 21676
From: Houston, TX , USA
Registered: Dec 2001


Feedback score:    (15)
Leave feedback





Total ratings: 415
Rate this member

Report this Post05-10-2004 10:02 PM Click Here to See the Profile for jscott1Send a Private Message to jscott1Direct Link to This Post
It looks good so far. I really intended to do a custom dash but did the Firebird instead. The firebird door panels would move those controls back enough to be usable. Keep us posted.

- Jonathan

------------------
If you find my advice useful, then please give me a positive rating, thanks...

1988 GT (Firebird Interior),1988 Coupe (Daily Driver), 1985 SE (Project Car), 1985 Coupe (parts car), Firebird Interior Installation Website

IP: Logged
doublec4
Member
Posts: 8289
From: Oakville, Ontario, Canada
Registered: Jun 2003


Feedback score:    (20)
Leave feedback





Total ratings: 150
Rate this member

Report this Post05-11-2004 12:04 AM Click Here to See the Profile for doublec4Send a Private Message to doublec4Direct Link to This Post
If the interior turns out like the exterior you'll have one hell of a car.

------------------
1986 Fiero SE

IP: Logged
Borgio
Member
Posts: 221
From: Kokomo, Indiana, USA
Registered: Oct 2001


Feedback score: N/A
Leave feedback

Rate this member

Report this Post05-11-2004 02:27 AM Click Here to See the Profile for BorgioSend a Private Message to BorgioDirect Link to This Post
 
quote
Originally posted by bsculptor:

shhhh ... dont say that out loud.
im going to have to redo that also . still thinking ...


Oops, sorry. I'm sure you'll get that and the center console thing worked out. It looks really cool though and you're right about there being a lot of room in the stock fiero.

IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery
Real-Time Chat | Fiero Related Auctions on eBay



Copyright (c) 1999, C. Pennock