Pennock's Fiero Forum
  Technical Discussion & Questions - Archive
  ALDL Connector

T H I S   I S   A N   A R C H I V E D   T O P I C
  
Email This Page to Someone! | Printable Version
ALDL Connector by James_GT
Started on: 05-16-2009 07:24 PM
Replies: 5
Last post by: theogre on 10-03-2009 07:48 PM
James_GT
Member
Posts: 505
From: Melbourne, Victoria, Australia
Registered: Dec 2008

Feedback score: (1)
Leave feedback

Rate this member
Report this Post05-16-2009 07:24 PM Click Here to See the Profile for James_GTSend a Private Message to James_GTDirect Link to This Post
Could somebody please tell me what each terminal does?

I've got an 87GT Auto and I'm looking for the TCC terminal. I think it might be "F" but I'm not sure.

Cheers.

------------------
James

1987 Pontiac Fiero GT (RHD)

IP: Logged
PFF
System Bot
Mike Gonzalez
Member
Posts: 5093
From: Colorado Springs, CO. USA
Registered: Jul 2001

Feedback score: (1)
Leave feedback





Total ratings: 130
Rate this member
Report this Post05-16-2009 07:27 PM Click Here to See the Profile for Mike GonzalezSend a Private Message to Mike GonzalezDirect Link to This Post
It is F

IP: Logged
James_GT
Member
Posts: 505
From: Melbourne, Victoria, Australia
Registered: Dec 2008

Feedback score: (1)
Leave feedback

Rate this member
Report this Post05-16-2009 07:29 PM Click Here to See the Profile for James_GTSend a Private Message to James_GTDirect Link to This Post
Thanks
IP: Logged
ALJR
Member
Posts: 3765
From: Massachusetts
Registered: Jul 2009

Feedback score:    (18)
Leave feedback

Rate this member
Report this Post10-03-2009 12:30 PM Click Here to See the Profile for ALJRSend a Private Message to ALJRDirect Link to This Post
Is that the same pin-out for the 2.8? My 88gt is different...

If I am looking at the ALDL while its installed, I have pins in the connector at:
A, B, D, E, F, G

No pins in locations:
C, M, L, K J, H

I would have to "assume" the Serial Data listed at pin M is actually at pin E on mine???
IP: Logged
josef644
Member
Posts: 6939
From: Dickinson, Texas USA
Registered: Nov 2006

Feedback score:    (71)
Leave feedback





Total ratings: 103
Rate this member
Report this Post10-03-2009 05:04 PM Click Here to See the Profile for josef644Send a Private Message to josef644Direct Link to This Post
Two different baud rates. The low one ,160 baud , works on 'E', and the higher one, 8192 baud, comes threw 'M' They dont work at the same time. You either have one or the other. My 88 was a 2.5, and the ALDL was factory wired for 'M', 'E' was empty.
IP: Logged
theogre
Member
Posts: 32520
From: USA
Registered: Mar 99

Feedback score: N/A
Leave feedback





Total ratings: 572
Rate this member
Report this Post10-03-2009 07:48 PM Click Here to See the Profile for theogreClick Here to visit theogre's HomePageSend a Private Message to theogreDirect Link to This Post
87-88 L4 use P4 ECM and ALDL data pin M. (Will Not Work with WinALDL or TFS.)
84-86 L4 and All V6 uses C3 ECM and ALDL data pin E.

All other ALDL pin are the same.
See Cave

------------------
Dr. Ian Malcolm: Yeah, but your scientists were so preoccupied with whether or not they could, they didn't stop to think if they should.
(Jurassic Park)

The Ogre's Fiero Cave (It's also at the top of every forum page...)

IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery
Real-Time Chat | Fiero Related Auctions on eBay



 Copyright (c) 1999, C. Pennock