Pennock's Fiero Forum
  Technical Discussion & Questions - Archive
  Screw size for hood release handle?

T H I S   I S   A N   A R C H I V E D   T O P I C
  
Email This Page to Someone! | Printable Version
Screw size for hood release handle? by Fiero_Adam
Started on: 09-12-2008 05:10 PM
Replies: 5
Last post by: mrfiero on 09-17-2008 12:01 AM
Fiero_Adam
Member
Posts: 1624
From: Oklahoma
Registered: Apr 2005

Feedback score:    (9)
Leave feedback

Rate this member
Report this Post09-12-2008 05:10 PM Click Here to See the Profile for Fiero_AdamSend a Private Message to Fiero_AdamDirect Link to This Post
I'm going through my container of interior fasteners, but I can't find a screw that fits the hood release handle. There are 3 of them. I thought they were the standard torx screws that hold on all of the trim pieces on the dash, but they don't fit. I think these need to be fine thread, but not sure.

------------------

IP: Logged
PFF
System Bot
mrfiero
Member
Posts: 9014
From: Colorful Colorado
Registered: Mar 99

Feedback score:    (91)
Leave feedback





Total ratings: 150
Rate this member
Report this Post09-12-2008 06:04 PM Click Here to See the Profile for mrfieroSend a Private Message to mrfieroDirect Link to This Post
They are actually phillips head screws, not torx. I have no idea on the size though they are pretty small (shorter than the torx screws).
IP: Logged
Fiero_Adam
Member
Posts: 1624
From: Oklahoma
Registered: Apr 2005

Feedback score:    (9)
Leave feedback

Rate this member
Report this Post09-13-2008 01:29 AM Click Here to See the Profile for Fiero_AdamSend a Private Message to Fiero_AdamDirect Link to This Post
Ah ha. I'll have to look through my fasteners again. I didn't even think about a phillips screw, because everything else is a T15! Hopefully someone will know the size, though. I wouldn't be surprised if I actually lost them.
IP: Logged
mrfiero
Member
Posts: 9014
From: Colorful Colorado
Registered: Mar 99

Feedback score:    (91)
Leave feedback





Total ratings: 150
Rate this member
Report this Post09-16-2008 07:43 PM Click Here to See the Profile for mrfieroSend a Private Message to mrfieroDirect Link to This Post
Hey.....I pulled off these screws from a junked Fiero today. LMK if you need them.
IP: Logged
Fiero_Adam
Member
Posts: 1624
From: Oklahoma
Registered: Apr 2005

Feedback score:    (9)
Leave feedback

Rate this member
Report this Post09-16-2008 11:59 PM Click Here to See the Profile for Fiero_AdamSend a Private Message to Fiero_AdamDirect Link to This Post
Oops. I forgot to reply back saying I found some that work. Sorry. Thanks for the offer though.
IP: Logged
mrfiero
Member
Posts: 9014
From: Colorful Colorado
Registered: Mar 99

Feedback score:    (91)
Leave feedback





Total ratings: 150
Rate this member
Report this Post09-17-2008 12:01 AM Click Here to See the Profile for mrfieroSend a Private Message to mrfieroDirect Link to This Post
No prob. I was at the junkyard, grabbed them and "dropped" them in my pocket, so no loss.
IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery
Real-Time Chat | Fiero Related Auctions on eBay



 Copyright (c) 1999, C. Pennock