Pennock's Fiero Forum
  Technical Discussion & Questions - Archive
  GTP pulley

T H I S   I S   A N   A R C H I V E D   T O P I C
  
Email This Page to Someone! | Printable Version
GTP pulley by GT-maniac
Started on: 04-13-2008 08:28 PM
Replies: 4
Last post by: Fie Ro on 04-14-2008 01:55 PM
GT-maniac
Member
Posts: 597
From: Leduc, Alberta
Registered: May 2000

Feedback score: N/A
Leave feedback

Rate this member
Report this Post04-13-2008 08:28 PM Click Here to See the Profile for GT-maniacSend a Private Message to GT-maniacDirect Link to This Post
Anyone know where I can find the 98 GTP pulley needed for the 3800SC engine swap ? No one seems to have the pulley at clubgp now and I don't see a listing for it on GMPartsDirect. Also does anybody have drawings with measurements for the arm I need made for the low mount alt setup ?. Any web links would be appreciated.
IP: Logged
PFF
System Bot
FIEROFLYER
Member
Posts: 3974
From:
Registered: Oct 2002

Feedback score:    (13)
Leave feedback





Total ratings: 180
Rate this member
Report this Post04-13-2008 08:35 PM Click Here to See the Profile for FIEROFLYERSend a Private Message to FIEROFLYERDirect Link to This Post
If it is a stock super charger pulley you need I have a few good ones from cars that I swapped smaller pulleys onto. For making your own mounts and brackets take a look through the photos in the link below my sig there may be some answers in there for you. Dan

------------------


Signature compliments of F-I-E-R-O
2003 3800SC series II powered
www.photosled.com/showgallery.php/cat/631
www.photosled.com/showgallery/cat/1583

IP: Logged
GT-maniac
Member
Posts: 597
From: Leduc, Alberta
Registered: May 2000

Feedback score: N/A
Leave feedback

Rate this member
Report this Post04-13-2008 11:32 PM Click Here to See the Profile for GT-maniacSend a Private Message to GT-maniacDirect Link to This Post
Ok thanks for the links, here's the pulley I was looking for.



Do you have a center to center measurement of the two main bolts on this bracket ?




IP: Logged
darkhorizon
Member
Posts: 12279
From: Flint Michigan
Registered: Jan 2006

Feedback score: (1)
Leave feedback





Total ratings: 451
Rate this member
Report this Post04-14-2008 02:56 AM Click Here to See the Profile for darkhorizonSend a Private Message to darkhorizonDirect Link to This Post


That alternator bracket can be whatever size you want, the measurement of that strut is not that important. Make sure you have a mount going to the rear of that alternator, 2 points is hard on the casting.

------------------
Losing sight of our roots in the cathode rays.



Ultimate 3800 swap thread

IP: Logged
Fie Ro
Member
Posts: 3735
From: Soest, The Netherlands
Registered: Sep 2001

Feedback score: N/A
Leave feedback





Total ratings: 132
Rate this member
Report this Post04-14-2008 01:55 PM Click Here to See the Profile for Fie RoSend a Private Message to Fie RoDirect Link to This Post
 
quote
Originally posted by GT-maniac:
Ok thanks for the links, here's the pulley I was looking for.



hey I looked at that pic and realized I posted it sometime ago...lol
Jegs has replacement pullies
IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery | Ogre's Cave
Real-Time Chat | Fiero Related Auctions on eBay



 Copyright (c) 1999, C. Pennock