Pennock's Fiero Forum
  Technical Discussion & Questions - Archive
  breather grommet?

T H I S   I S   A N   A R C H I V E D   T O P I C
  
Email This Page to Someone! | Printable Version
breather grommet? by Doc-
Started on: 03-03-2006 09:42 AM
Replies: 5
Last post by: spark1 on 03-04-2006 09:23 PM
Doc-
Member
Posts: 185
From: Waldorf, MD, USA
Registered: Oct 2005

Feedback score: N/A
Leave feedback

Rate this member
Report this Post03-03-2006 09:42 AM Click Here to See the Profile for Doc-Send a Private Message to Doc-Direct Link to This Post
Hello all. Does anyone know if there is a HELP part number for the breather grommet on the 2.5 (breather between valve cover and air cleaner housing). I was replacing the PCV and its elbow grommet and realized the breather and its grommet were leaking too. I checked several auto parts websites and could only find the PCV grommet, not the breather grommet. Are they the same by chance?
IP: Logged
PFF
System Bot
3800superfast
Member
Posts: 8568
From: ohio U.S.
Registered: Apr 2004

Feedback score: N/A
Leave feedback





Total ratings: 191
Rate this member
Report this Post03-03-2006 09:45 AM Click Here to See the Profile for 3800superfastSend a Private Message to 3800superfastDirect Link to This Post
Hi, I think they are on the 2.8--not sure on the 4clyinder --did you check the Fiero store?
IP: Logged
Doc-
Member
Posts: 185
From: Waldorf, MD, USA
Registered: Oct 2005

Feedback score: N/A
Leave feedback

Rate this member
Report this Post03-03-2006 04:31 PM Click Here to See the Profile for Doc-Send a Private Message to Doc-Direct Link to This Post
The fiero store doesn't have them listed for the duke. I guess I'll just pull mine off and look throught the HELP aisle. Thanks.
IP: Logged
edfiero
Member
Posts: 974
From: Coatesville, PA
Registered: Nov 2004

Feedback score: N/A
Leave feedback

Rate this member
Report this Post03-04-2006 07:26 PM Click Here to See the Profile for edfieroSend a Private Message to edfieroDirect Link to This Post
What I've done when I can't find replacement gromments anymore, is to take them out and clean them, and put them back in with RTV Sealant. That usually will plug up any leaks. And if you use black, its hardly noticable.
IP: Logged
maryjane
Member
Posts: 70120
From: Copperas Cove Texas
Registered: Apr 2001

Feedback score: (4)
Leave feedback





Total ratings: 436
Rate this member
Report this Post03-04-2006 07:39 PM Click Here to See the Profile for maryjaneSend a Private Message to maryjaneDirect Link to This Post
The # I have written down in my little parts notebook is:
10037288=grommet--breather to valve cover.
Fits an 84 is all I can tell you.
IP: Logged
spark1
Member
Posts: 11159
From: Benton County, OR
Registered: Dec 2002

Feedback score: (1)
Leave feedback





Total ratings: 175
Rate this member
Report this Post03-04-2006 09:23 PM Click Here to See the Profile for spark1Send a Private Message to spark1Direct Link to This Post
The breather grommet is the same for all years of the 2.5L, 10037287, Dorman - HELP! 42322. The same grommet is used on the 87 & 88 PCV valve that plugs directly into the valve cover.

The 84 - 86 apparently use the number above (10037288 or Dorman - HELP! 42310) to fit the 90° elbow that is between the PCV valve and valve cover (the 87 - 88 style PCV valve has a built-in 90° elbow).

[This message has been edited by spark1 (edited 03-05-2006).]

IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery
Real-Time Chat | Fiero Related Auctions on eBay



 Copyright (c) 1999, C. Pennock