Pennock's Fiero Forum
  Technical Discussion & Questions - Archive
  3800sc torque specs

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Email This Page to Someone! | Printable Version


3800sc torque specs by ohio86se
Started on: 05-10-2005 03:07 PM
Replies: 10
Last post by: AnimalGT on 06-14-2005 08:24 AM
ohio86se
Member
Posts: 1308
From: akron, ohio, summit
Registered: Mar 2002


Feedback score: N/A
Leave feedback





Total ratings: 52
Rate this member

Report this Post05-10-2005 03:07 PM Click Here to See the Profile for ohio86seClick Here to visit ohio86se's HomePageSend a Private Message to ohio86seDirect Link to This Post
im looking for information or a link to a site that will give me engine torque specs. like the bearing caps, intake manifold, exhaust manifold and sc,ect.........

------------------

" DRIVE IT LIKE YOU LOVE IT"

IP: Logged
PFF
System Bot
ohio86se
Member
Posts: 1308
From: akron, ohio, summit
Registered: Mar 2002


Feedback score: N/A
Leave feedback





Total ratings: 52
Rate this member

Report this Post05-10-2005 10:26 PM Click Here to See the Profile for ohio86seClick Here to visit ohio86se's HomePageSend a Private Message to ohio86seDirect Link to This Post
bump

------------------

" DRIVE IT LIKE YOU LOVE IT"

IP: Logged
Darth Fiero
Member
Posts: 5922
From: Waterloo, Indiana
Registered: Oct 2002


Feedback score: (5)
Leave feedback





Total ratings: 361
Rate this member

Report this Post05-11-2005 01:16 AM Click Here to See the Profile for Darth FieroClick Here to visit Darth Fiero's HomePageSend a Private Message to Darth FieroDirect Link to This Post

2000 Pontiac Grand Prix 3.8L

--------------------------------------------------------------------------------

Fastener Tightening Specifications
Application
Specifications

Metric
English

Accelerator Control Cable Bracket Bolt
16 N·m
12 lb ft

Air Injection Check Valve Pipe to Exhaust Manifold Bolt (with NC8 California Emissions)
10 N·m
89 lb in

Air Injection Check Valve to Bracket Bolt (with NC8 California Emissions)
25 N·m
18 lb ft

Balance Shaft Driven Gear Bolt
22 N·m + 70°
16 lb ft + 70°

Balance Shaft Retainer Bolt
30 N·m
22 lb ft

Camshaft Position Sensor Bolt
10 N·m
89 lb in

Camshaft Sprocket Bolt
100 N·m + 90°
74 lb ft + 90°

Camshaft Thrust Plate Bolt
15 N·m
11 lb ft

Canister Purge Solenoid Valve Bracket Bolt (VIN K)
50 N·m
37 lb ft

Canister Purge Vacuum Switch Bolt (VIN K)
50 N·m
37 lb ft

Connecting Rod Cap Bolt
27 N·m + 50°
20 lb ft + 50°

Crankshaft Balancer Bolt
150 N·m + 76°
111 lb ft + 76°

Crankshaft Main Bearing Cap Bolt
40 N·m + 110°
30 lb ft + 110°

Crankshaft Main Bearing Cap Bolt (Side)
15 N·m + 45°
11 lb ft + 45°

Crankshaft Position Sensor Stud
30 N·m
22 lb ft

Crankshaft Rear Oil Seal Housing Bolt
15 N·m + 50°
11 lb ft + 50°

Cylinder Head Bolt
50 N·m + 120°
37 lb ft + 120°

Drive Belt Tensioner Bracket Bolt/Nut
50 N·m
37 lb ft

Drive Belt Tensioner Bracket Stud
6 N·m
53 lb in

EGR Valve Adapter Bolt
50 N·m
37 lb ft

EGR Valve Inlet Pipe Bolt
29 N·m
21 lb ft

EGR Valve Nut
29 N·m
21 lb ft

EGR Valve Outlet Pipe Bolt/Nut
29 N·m
21 lb ft

Engine Block Coolant Drain Plug (VIN 1)
18 N·m
13 lb ft

Engine Block Coolant Drain Plug (VIN K)
30 N·m
22 lb ft

Engine Block Oil Gallery Plug
30 N·m
22 lb ft

Engine Coolant Temperature Sensor
25 N·m
18 lb ft

Engine Flywheel Bolt
15 N·m + 50°
11 lb ft + 50°

Engine Front Cover Bolt/Stud
20 N·m + 40°
15 lb ft + 40°

Engine Lift Bracket Bolt/Nut/Stud
30 N·m
22 lb ft

Engine Mount Nut, Lower
78 N·m
58 lb ft

Engine Mount Nut, Upper
78 N·m
58 lb ft

Engine Oil Pressure Indicator Switch
16 N·m
12 lb ft

Exhaust Crossover Heat Shield Nut
20 N·m
15 lb ft

Exhaust Crossover Pipe Bolt/Stud
18 N·m
13 lb ft

Exhaust Manifold Bolt/Nut
30 N·m
22 lb ft

Exhaust Manifold Heat Shield Nut
20 N·m
15 lb ft

Exhaust Manifold Pipe Stud
6 N·m
53 lb in

Exhaust Manifold Stud (Inner)
30 N·m
22 lb ft

Exhaust Manifold Stud (Outer)
10 N·m
89 lb in

Fuel Injector Rail Nut
10 N·m
89 lb in

Fuel Injector Rail Stud
25 N·m
18 lb ft

Fuel Injector Sight Shield Bracket Nut
30 N·m
22 lb ft

Generator Brace Bracket Bolt
50 N·m
37 lb ft

Heated Oxygen Sensor
42 N·m
31 lb ft

ICM Bolt (VIN 1)
30 N·m
22 lb ft

ICM Nut
50 N·m
37 lb ft

ICM Stud (VIN K)
6 N·m
53 lb in

ICM Wiring Harness Bolt
2 N·m
18 lb in

Idler Pulley Bolt
50 N·m
37 lb ft

Idler Pulley Bracket Bolt
30 N·m
22 lb ft

Lower Intake Manifold Bolt
15 N·m
11 lb ft

MAP Sensor Bolt (VIN 1)
3 N·m
27 lb in

MAP Sensor Bracket Bolt (VIN 1)
30 N·m
22 lb ft

Oil Cooler Adapter Connector
50 N·m
37 lb ft

Oil Filter
30 N·m
22 lb ft

Oil Filter Adapter Bolt
15 N·m + 50°
11 lb ft + 50°

Oil Level Indicator Switch
20 N·m
15 lb ft

Oil Level Indicator Tube Nut
19 N·m
14 lb ft

Oil Pan Bolt
14 N·m
125 lb in

Oil Pan Drain Plug
30 N·m
22 lb ft

Oil Pump Cover Screw
11 N·m
98 lb in

Oil Pump Pipe and Screen Bolt
15 N·m
11 lb ft

Power Brake Booster Heat Shield Nut
20 N·m
15 lb ft

Spark Plug
27 N·m
20 lb ft

Starter Motor Heat Shield Bolt
30 N·m
22 lb ft

Supercharger Bolt/Stud (VIN 1)
23 N·m
17 lb ft

Supercharger Bypass Valve and Fuel Pressure Regulator Valve Harness Bolt (VIN 1)
10 N·m
89 lb in

Supercharger Bypass Valve Nut (VIN 1)
8 N·m
71 lb in

Throttle Body Nut
10 N·m
89 lb in

Throttle Body Support Bolt (VIN K)
10 N·m
89 lb in

Timing Chain Dampener Bolt
22 N·m
16 lb ft

Upper Intake Manifold Bolt (VIN K)
10 N·m
89 lb in

Vacuum Solenoid Valve Bolt (with NC8 California Emissions)
10 N·m
89 lb in

Valve Lifter Guide Retainer Bolt
30 N·m
22 lb ft

Valve Rocker Arm Bolt
15 N·m + 90°
11 lb ft + 90°

Valve Rocker Arm Cover Bolt
10 N·m
89 lb in

Water Outlet Bolt
27 N·m
20 lb ft

Water Pump Bolt
15 N·m + 80°
11 lb ft + 80°

Water Pump Pulley Bolt
13 N·m
116 lb in

Wiring Harness Shield Bolt/Nut
10 N·m
89 lb in


------------------
power corrupts. absolute power corrupts absolutely.

Custom Computer Tuning | Engine Conversions | Turbocharging | www.gmtuners.com

IP: Logged
Darth Fiero
Member
Posts: 5922
From: Waterloo, Indiana
Registered: Oct 2002


Feedback score: (5)
Leave feedback





Total ratings: 361
Rate this member

Report this Post05-11-2005 01:24 AM Click Here to See the Profile for Darth FieroClick Here to visit Darth Fiero's HomePageSend a Private Message to Darth FieroDirect Link to This Post

Darth Fiero

5922 posts
Member since Oct 2002
IP: Logged
Darth Fiero
Member
Posts: 5922
From: Waterloo, Indiana
Registered: Oct 2002


Feedback score: (5)
Leave feedback





Total ratings: 361
Rate this member

Report this Post05-11-2005 01:27 AM Click Here to See the Profile for Darth FieroClick Here to visit Darth Fiero's HomePageSend a Private Message to Darth FieroDirect Link to This Post

Darth Fiero

5922 posts
Member since Oct 2002
Install the crankshaft main bearing cap bolts. Start the crankshaft main bearing cap bolts by hand. Ensure the bottom of the crankshaft main bearing cap is parallel to the bottom of the channel. Tighten

Tighten the crankshaft main bearing cap bolts in equal increments. Do not completely tighten one bolt at a time to prevent the cap from being cocked.

Tighten the bolts to 70 N·m (52 lb ft) to fully seat the crankshaft main bearing caps. Loosen the bolts 360 degrees counterclockwise.

Tighten the bolts to 20 N·m (15 lb ft), then 40 N·m (30 lb ft).

Use a torque-angle meter tool to tighten the bolts in steps: 35 degrees + 35 degrees + 40 degrees for a total of 110 degrees.

Install the side main bolts. Apply GM P/N United States 12345493, GM P/N Canada 10953488 or the equivalent to the side main bolts. Tighten

Tighten the side crankshaft main bearing cap bolts to 15 N·m (11 lb ft). Use J 36660-A to tighten the bolts an additional 45 degrees.

IP: Logged
Darth Fiero
Member
Posts: 5922
From: Waterloo, Indiana
Registered: Oct 2002


Feedback score: (5)
Leave feedback





Total ratings: 361
Rate this member

Report this Post05-11-2005 01:29 AM Click Here to See the Profile for Darth FieroClick Here to visit Darth Fiero's HomePageSend a Private Message to Darth FieroDirect Link to This Post

Darth Fiero

5922 posts
Member since Oct 2002
IP: Logged
Darth Fiero
Member
Posts: 5922
From: Waterloo, Indiana
Registered: Oct 2002


Feedback score: (5)
Leave feedback





Total ratings: 361
Rate this member

Report this Post05-11-2005 01:32 AM Click Here to See the Profile for Darth FieroClick Here to visit Darth Fiero's HomePageSend a Private Message to Darth FieroDirect Link to This Post

Darth Fiero

5922 posts
Member since Oct 2002

Sealers, Adhesives, and Lubricants
Application
Type of Material
GM Part Number


Accelerator Control Cable Bracket Bolt Threads
Threadlock
12345382


Coolant Temperature Sensor Threads
Sealant
12346004


Crankshaft Position Sensor Bolt/Stud Threads
Threadlock
12345382


Crankshaft Side Main Bolt Threads
Threadlock
12345493


Engine Block Coolant Drain Plug Threads
Sealant
12346004


Engine Block Oil Gallery Plug Threads
Sealant
12346004


Engine Front Cover Bolt Threads
Sealant
12346004


Engine Oil
Oil-10W-30
12345616


Engine Oil Supplement
Lubricant
1052367


Exhaust Manifold Bolt and Stud Threads
Threadlock
12345493


Intake Manifold Bolt Threads -Lower
Threadlock
12345493


Intake Manifold Coolant Pipe
Sealant
12345493


Intake Manifold to Engine Block Mating Surface
Sealant
12346286


Knock Sensor Threads
Sealant
12346004


Oil Filter Bypass Hole Plug Threads
Sealant
12346004


Oil Pan Bolt Threads
Threadlock
12345382


Oil Pressure Switch Threads
Sealant
12346004


Piston and Piston Pin
Oil-10W-30
12345616


Rear Crankshaft Main Bearing Cap
Sealant
1052942


Supercharger Oil
Lubricant
12345982


Valve Lifter and Camshaft Prelube
Lubricant
12345501


Valve Rocker Arm Cover Bolt Threads
Threadlock
12345382


Valve Rocker Arm Bolt Threads
Threadlock
12345493


Valve Train Component Prelube
Lubricant
1052367


IP: Logged
mcaanda
Member
Posts: 3652
From: Grand Junction Colorado
Registered: Mar 2003


Feedback score:    (19)
Leave feedback





Total ratings: 129
Rate this member

Report this Post05-11-2005 09:54 AM Click Here to See the Profile for mcaandaSend a Private Message to mcaandaDirect Link to This Post
Dear Lord Ryan, if I was able to give multiple +'s, you'd damn near have about a hundred by now.

Great work, I dont actually need that info as of today, but you can belive that it was just saved, and just converted into a .pdf file for possible future use.

--Allen

------------------

IP: Logged
ohio86se
Member
Posts: 1308
From: akron, ohio, summit
Registered: Mar 2002


Feedback score: N/A
Leave feedback





Total ratings: 52
Rate this member

Report this Post05-11-2005 10:25 AM Click Here to See the Profile for ohio86seClick Here to visit ohio86se's HomePageSend a Private Message to ohio86seDirect Link to This Post
thanks....ryan
IP: Logged
Darth Fiero
Member
Posts: 5922
From: Waterloo, Indiana
Registered: Oct 2002


Feedback score: (5)
Leave feedback





Total ratings: 361
Rate this member

Report this Post06-14-2005 04:32 AM Click Here to See the Profile for Darth FieroClick Here to visit Darth Fiero's HomePageSend a Private Message to Darth FieroDirect Link to This Post
bump
IP: Logged
AnimalGT
Member
Posts: 1118
From: Chicago, IL
Registered: Jul 2001


Feedback score: (4)
Leave feedback

Rate this member

Report this Post06-14-2005 08:24 AM Click Here to See the Profile for AnimalGTSend a Private Message to AnimalGTDirect Link to This Post
Darth... thank you. I'd give you 1000 +s if I could.
IP: Logged
PFF
System Bot



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery
Real-Time Chat | Fiero Related Auctions on eBay



Copyright (c) 1999, C. Pennock