Pennock's Fiero Forum
  Technical Discussion & Questions - Archive
  Need dimensions for 3800 and S5000

T H I S   I S   A N   A R C H I V E D   T O P I C
  
Email This Page to Someone! | Printable Version
Need dimensions for 3800 and S5000 by smokinjoefission
Started on: 05-05-2004 03:37 PM
Replies: 6
Last post by: rroberts on 08-24-2004 10:55 PM
smokinjoefission
Member
Posts: 138
From: Vancouver, BC, Canada
Registered: Jan 2004

Feedback score: N/A
Leave feedback

Rate this member
Report this Post05-05-2004 03:37 PM Click Here to See the Profile for smokinjoefissionClick Here to visit smokinjoefission's HomePageSend a Private Message to smokinjoefissionDirect Link to This Post
Some of you might figure out where I'm going with this, but I need:

The easy one:
physical dimensions of the 3800 Series II (length, width, height) with water pump and accessory pullies

The hard one:
the same dimensions for the 86 - 89 Audi 5000 FWD manual transmission
I've got some great information at http://www.statikdesign.com/scratchbuilt/drivetrain/transmission.html but no dimensions that I can find. Hoping someone in the PFF community might have this information.

Thanks in advance

------------------

IP: Logged
PFF
System Bot
smokinjoefission
Member
Posts: 138
From: Vancouver, BC, Canada
Registered: Jan 2004

Feedback score: N/A
Leave feedback

Rate this member
Report this Post05-06-2004 11:05 AM Click Here to See the Profile for smokinjoefissionClick Here to visit smokinjoefission's HomePageSend a Private Message to smokinjoefissionDirect Link to This Post
^^^ PMUB ^^^
IP: Logged
smokinjoefission
Member
Posts: 138
From: Vancouver, BC, Canada
Registered: Jan 2004

Feedback score: N/A
Leave feedback

Rate this member
Report this Post05-07-2004 12:17 AM Click Here to See the Profile for smokinjoefissionClick Here to visit smokinjoefission's HomePageSend a Private Message to smokinjoefissionDirect Link to This Post
No one's got a 3800 on an engine stand and a tape measure ?
IP: Logged
FieroBUZZ
Member
Posts: 3320
From: Ontario, Canada
Registered: Feb 2001

Feedback score: N/A
Leave feedback





Total ratings: 103
Rate this member
Report this Post05-07-2004 10:04 AM Click Here to See the Profile for FieroBUZZSend a Private Message to FieroBUZZDirect Link to This Post
No, we all have a 3800 sitting in the garage. We just think you're barking up the wrong tree.

Free bump......

IP: Logged
joeschmotty
Member
Posts: 443
From: Tulsa, OK
Registered: Mar 2003

Feedback score: N/A
Leave feedback

Rate this member
Report this Post08-23-2004 09:43 PM Click Here to See the Profile for joeschmottySend a Private Message to joeschmottyDirect Link to This Post
bumping because i want to know too..
specifically for the engine please. can anyone get physical dimensions for the engine??
IP: Logged
cccharlie
Member
Posts: 2006
From: North Smithfield, RI
Registered: Jan 2003

Feedback score: N/A
Leave feedback





Total ratings: 65
Rate this member
Report this Post08-24-2004 10:05 AM Click Here to See the Profile for cccharlieSend a Private Message to cccharlieDirect Link to This Post
Bunch of audi transaxle data here:

http://www.gt40club.clara.net/technics.htm

IP: Logged
rroberts
Member
Posts: 403
From: Des Moines
Registered: Apr 2003

Feedback score: (1)
Leave feedback

Rate this member
Report this Post08-24-2004 10:55 PM Click Here to See the Profile for rrobertsSend a Private Message to rrobertsDirect Link to This Post
Not sure what you are needing but it is 21" long and about 19" wide. It is shorter then the 2.8 but it is wider.
If that will help.
Rod
IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery
Real-Time Chat | Fiero Related Auctions on eBay



 Copyright (c) 1999, C. Pennock