??

STAR WARS GEEK!!! lol Join the club

Hey i am not a geek i am a Star Wars NUT

auto or stick? If you are talking autos then almost any 3 spped tranny that is pre 90.

I have a 5-sp. out of an '88 coupe that would work just fine with your '84. This is the Isuzu tranny used on all '85-'88 4 cylinder Fieros.

I have the tranny, the mount brackets and can get some decent cables too. All you need are some new mounts and you're in business.

LMk if you are interested.

How much are you looking to get for your 5sp ??

I'm looking for a 5-speed for a V6.

Does only the getrag fit that? does anyone have one?

and if the izuzu will fit, what izuzu's can you grab one from.

Cavalier, Sunbird, Citation

[This message has been edited by rogergarrison (edited 12-30-2001).]

This has probably been asked before also...

What other vehicles used a Getrag that would work in a Fiero..???
( besides the Corsica/Barretta )

------------------
'84 SE
'84 SE (Strictly Parts Car)
'86 SE
'00 HD 1200XL Sportster

http://www.rodneydickman.com/getraginfo.htm
(Getrag conversion articale)

Yeah ok know i am going to get chewed out for this but i have a manual 4speed in it now what is needed to go to a 3 apeed auto
i have access to a free 3 speed auto from a 86 buick century

Swapping over to an auto. is a very involved process......it's more than just installing teh tranny. You'll have wiring issues, ECM issues,radiator issues, etc.

I am looking to get $50 for the Isuzu 5-sp. that I have. That includes the tranny and the brackets. I can get some cables and a used slave for you, but they will be extra (have to snag them from a junkyard).

The Isuzu swap is straight forward......just install it and you're done. Obviously you should do a clutch job at this time, so factor that in.

LMK if you are interested and we'll work things out.

Hey dose the cluch out of a 4 speed work and how much extra is the Cables (And what ever else i would need ???

I'm not sure about the clutch......it may work. If it shows any signs of wear I would replace it. Since the tranny will be out it is the ideal time to do a clutch job and it will save you the hassle of doing it again in the near future. I might have a decent used clutch from an Isuzu somewhere, so I can throw that in too, if you want it.

I actually have a slave cylinder (used) that I will include in the $50 price. I can't guarantee that it will work or how long it will last, but at least you will have one (your '84s slave is different).

The cables will be whatever I have to pay the junkyard for them, but probably less than $20 for the pair.

LMK if you are interested.

Did the 84s have a cluch Slave cylinder if not what do i need to do (Do i need to **** any thing ??

The slave cylinder on your '84 will not work with the Isuzu (or any other) tranny. It is an '84 only design.

Yes, it will bolt up to a 3.1 (as well as a 2.8, 3.4, etc.). It has the same bolt pattern as all other Fiero trannies (all Fiero trannies are interchangeable).

I mean is the Salve a Bolt on or do i have to make ajustments

[This message has been edited by ig88vsbobafett (edited 12-29-2001).]

hes rite about switching to auto from a stick. That what I wanted to do. It takes the complete dash wiring harness from an auto for just starters. My estimate for a new crate auto installed was over $5,000. If you want an auto, do what I did and just search for an auto car to start with.