 
     |
| Personalized decklid vents and other things (Page 24/49) |
|
freedom0226
|
MAY 23, 01:54 PM
|
|
|
Pm sent on the door sills..
|
|
|
|
grsychckn
|
JUN 20, 08:56 PM
|
|
Wanted to update with what silver 85 sc made for me.
|
|
|
|
kjc88gt
|
JUN 29, 09:41 PM
|
|
| quote | Originally posted by silver 85 sc:
Shifter surround pod $65.00. Not perfect yet, but really close. I have the latest revision ready to bend. 18 ga stainless
Rich |
|
Hey y'all- post some more pics!
Has anyone wrapped the pod? I'd like to see a pic or two of one wrapped.
I'm afraid it be pretty frickin hot sitting in texas sun all day.
I don't mind deleting the ash trays or keeping them. They do help hold the phone down but they don't have any other purpose. So post some pictures of the ash tray deleted too.
What are the options for this piece? Is it a one piece unit for the pod and the cover, or would I need the two pieces?
|
|
|
|
silver 85 sc
|
JUN 30, 12:07 AM
|
|
| quote | Originally posted by kjc88gt:
Hey y'all- post some more pics!
Has anyone wrapped the pod? I'd like to see a pic or two of one wrapped.
I'm afraid it be pretty frickin hot sitting in texas sun all day.
I don't mind deleting the ash trays or keeping them. They do help hold the phone down but they don't have any other purpose. So post some pictures of the ash tray deleted too.
What are the options for this piece? Is it a one piece unit for the pod and the cover, or would I need the two pieces? |
|
PM sent
|
|
|
|
infinitewill
|
JUN 30, 12:57 AM
|
|
Rich,
Any word on the project we discussed?
Lemme know 
Dr. W.------------------
Is your Fastback GT's trunk seal shot? My Gen III replacement GT trunk seals with solid molded corners are now in production. $95 + $15 flat rate shipping to the US (contact me for international shipping rates) or buy two and pay only a single shipping rate! More info can be found here GT Trunk Seal Project
|
|
|
|
a_bartle
|
JUL 06, 11:37 AM
|
|
|
Did the center console ever get finalized? If so, any pics?
|
|
|
|
silver 85 sc
|
JUL 06, 04:39 PM
|
|
| quote | Originally posted by a_bartle:
Did the center console ever get finalized? If so, any pics? |
|
I made 3 the last go around and have 2 on hand. They have a clean look to them, however I think that they should be covered. I took an existing shifter plate and cut a slit below the ashtray with a hacksaw so that the shifter plate would snap in. The only pictures I have is the prototype in my '86. As for appearance the new ones look cleaner. If I get the ambition to fight the 100º+ heat I will take another round of snap shots.
Rich
|
|
|
Christine
|
JUL 06, 11:54 PM
|
|
I would like to get the full set for the dash but I would like to have the radio hole cut for a single din stereo, could you do that?
| quote | Originally posted by silver 85 sc:
Here is a dash kit that is going out:
.jpg)
_1.jpg)
_(509x267)_1.jpg)
This is one of a couple going out this week.
Rich |
|
|
|
|
|
silver 85 sc
|
JUL 07, 11:25 AM
|
|
| quote | Originally posted by Christine:
I would like to get the full set for the dash but I would like to have the radio hole cut for a single din stereo, could you do that?
|
|
Like this?
Slot is centered over existing stock radio hole. It can be moved up or down if needed. Double check hole size. According to the chart I found on dimensions, the single din radio requires a 180mm long x 50mm high slot, and I would recommend a rear bracket for support.
Rich
|
|
|
Christine
|
JUL 07, 02:50 PM
|
|
That is exactly what I need and yes the hole size is correct the stereo is actually 179mmx50mm so 180mmx50mm might be a little snug but should work.
Do these go over the old bezels? If so, how do they cover the edges? My friend has a wood grain dash kit and you can see the old bezels around the edges do yours cover the edges? I see install pics in this thread but none have close ups of the edges do you have any pics of the edges close up?
Gauge cluster $15.00 18 ga stainless
Aux ga $5.00 18 ga stainless
Radio surround $10.00 18 ga stainless
Shifter surround $10.00 18 ga stainless – automatic with ashtrays
Is this pricing still correct?
| quote | Originally posted by silver 85 sc:
Like this?
Slot is centered over existing stock radio hole. It can be moved up or down if needed. Double check hole size. According to the chart I found on dimensions, the single din radio requires a 180mm long x 50mm high slot, and I would recommend a rear bracket for support.
Rich |
|
|
|
|
