 
     |
| Custom Fiberglass parts. (Page 15/47) |
|
Gokart
|
JUL 26, 05:48 PM
|
|
Hey Paul. How hard would it be to make these? http://www.sfxperformance.com/parts/AST1159.htm Don't know if there would be much of a demand. I love mine. It provides more privacy and less sunlight penetration. My complaints with the Astro Hammond's are the plastic is a little flimsy and it has curled in some areas due to the engine heat and it's also bulky. It comes out around 2 inches past the glass which I think isn't necessary if the louvres were angled down more.
Marc[This message has been edited by Gokart (edited 07-26-2011).]
|
|
|
|
ALJR
|
JUL 26, 07:27 PM
|
|
| quote | Originally posted by Gokart:
I love mine. It provides more privacy and less sunlight penetration. |
|
$8 in window tint has the same effect 
|
|
|
|
Tha Driver
|
JUL 26, 08:04 PM
|
|
|
|
|
RULOOKIN
|
JUL 26, 08:13 PM
|
|
| quote | Originally posted by ALJR:
Any desire to make a hood vent like this one? This is by far my favorite hood vent The ONLY thing I thing I would change would be to make the opening about 1-1.5" smaller; keep the same width, just not as tall; which would make it not a deep...
|
|
I seconnd that !!! I will buy one for sure
|
|
|
|
Tha Driver
|
JUL 26, 08:19 PM
|
|
|
|
|
Gokart
|
JUL 26, 08:31 PM
|
|
| quote | Originally posted by ALJR:
$8 in window tint has the same effect |
|
True but I'm liking the louvre look! When it finally melts away I'll pick up some tint 
| quote | Originally posted by Tha Driver:
Would be a pain to make & like most everything else only one person would probably buy it. 
EDIT: Thanks for the suggestion anyway. 
EDIT again: Can you downsize that image so that folks don't have to side scroll my thread to read it? 
|
|
Yes. You're probably right. Really no need for the pic so I deleted it.
Thanks for looking!
Marc
|
|
|
|
MulletproofMonk
|
JUL 26, 08:46 PM
|
|
|
|
|
Tha Driver
|
JUL 26, 10:20 PM
|
|
| quote | Originally posted by MulletproofMonk:
How does the rear Mustang scoop attach? Does it have bolts glassed in like some of the scoops I have seen? I like it.
|
|
It's made to bond/mold in. I could 'glass in some studs but it would take a little time & I'd have to find a source for studs (like the spoiler studs - they are readily available). The thing is it's made to fit well on the fastback decklid, but it really needs to be molded in on a notchie. I could do a slight re-design to fit the notchie better, but more time...(how many will I sell, again?).
~ Paul
aka "Tha Driver"
Custom Fiberglass Parts
|
|
|
|
ZarZ
|
JUL 27, 03:44 AM
|
|
Driver you have a pic of the STM deckled scoop resting in place from the back or corner but like 5 ft away?
|
|
|
|
Tha Driver
|
JUL 27, 05:45 AM
|
|
| quote | Originally posted by ZarZ:
Driver you have a pic of the STM deckled scoop resting in place from the back or corner but like 5 ft away? |
|
Sorry, no. What is it you're trying to determine? Just what it looks like at the same level as the decklid?
~ Paul
aka "Tha Driver"
Custom Fiberglass Parts
|
|
|
