Cant get the last Torx water pump bolt out! (Page 1/5)
jrr JUL 14, 02:29 PM




2.8L - I have the original 1988 Water pump currently. Trying to replace it with a new gates metal impeller pump and regular hex bolts which I bought from Rodney Dickman.

Eleven of the 12 bolts are out. Of course one remains frozen. I even tried and induction heater tool however there is not enough of the bolt protruding to allow the induction tool to work.

I have tried penetrating oil. Even tried to cut part of the pump away to get a lock plyer on it bit there is minimal space as you all know. I cant use a torch, or I am afraid to as there are wires behind the pump.

I am at the verge of striping the torx bolt if I apply any more pressure. There is just a bit of torx thread left to pull on before it strips completely. This is the bottom bolt.


See pictures. Any thoughts are appreciated.
steve308 JUL 14, 04:25 PM
Deleted.

[This message has been edited by steve308 (edited 07-14-2026).]

Vintage-Nut JUL 14, 05:07 PM

quote
I cant use a torch, or I am afraid to as there are wires behind the pump / I am at the verge of striping the torx bolt if I apply any more pressure.


Do NOT strip the Torx socket! IF the Torx socket is damaged, your nightmare will be complete...

In my experience, HEAT is the only way to remove 'frozen' bolts in one-piece....

To ME, clear the area if necessary, and then use a low flame to heat the bolt.

------------------
Original Owner of a Silver '88 GT
Six-Year 'Refurbishment' Nearly Finished...

Patrick JUL 14, 05:11 PM

This may or may not make any difference with your particular situation... but I've learned over the years not to remove all the other bolts (and/or nuts) if there's one that's still stuck. If anything, doing so only makes it even more difficult to loosen the stuck one.

I hope you have the special clamp in place which keeps the timing chain cover from getting loose (and breaking the gasket seal in the process).


quote
Originally posted by Patrick in This thread:



jrr JUL 14, 05:49 PM
Thanks Tool is on order and should be here in a few days
Dennis LaGrua JUL 14, 09:08 PM
That bolt is 40 years old and can be difficult to remove.. Applying heat and tapping it can work it free but in some cases by applying strong wrench pressure the head will break off.. That will make the job difficult as the remaining stud may need to be drilled out. Years back Ed Parks used a technique where he tack welded a nut to the broken stud and it wrenched right out. Right angle drills with Left handed bits can also be used to drill out studs with a bolt extractor. Let's hope that you get that bolt out in one piece
Mike in Sydney JUL 14, 10:01 PM
It sounds strange, I know, but try tightening the screw and then loosening it. If you can get it to turn a bit clockwise or may break the bonds holding it. Be Careful not to break the bolt.
jrr JUL 15, 09:11 AM
Thank you all for your responses! I am going to try and continue applying heat. Possibly I can press a nut over the torx head to get the induction heating tool to work. If all else fails I may have to put 11 of the 12 replacement hex bolts in and live with the old water pump until I can find someone to work on this. So far 3 shops said they wont touch it.

I even sent a message to Fiero Motive in Northern Florida with no response. The phone number does not go through either. I am sure I will get a flood of responses for this next comment, however the idea of running a 37+ year old motor at 220-230 degrees in South Florida does not sit well with me! Yesterday the temperature here was 97 degrees. Thanks again!
87GT3800SC5SPD JUL 15, 12:04 PM
This is how I resolved this frustrating situation more than 20 years ago. It is not a suggestion, but a story of how I ended several days of frustration, that resulted in successfully replacing my water pump. The last resort method, resembles something that happens by accident when you are removing something and are unable to see one of the hidden fasteners.

I had reached the limit of my patience and frustration of having no access to that stuck bolt and decided that the only way to get the bolt out, was to remove the water pump first. That was done quickly with a big pry bar and I broke the water pump away from the stubborn bolt. Call me crazy, but that gives you a lot more access to apply the more conventional stuck bolt removal methods. I then successfully installed the new water pump.

The next and last repair I did to the 2.8 engine was to replace it with a 3800.

This is a true story, but not always a best practice solution.

Good luck.

[This message has been edited by 87GT3800SC5SPD (edited 07-15-2026).]

Vintage-Nut JUL 15, 12:50 PM

quote
If all else fails I may have to put 11 of the 12 replacement hex bolts in and live with the old water pump until I can find someone to work on this.


To me, it is a bad idea....


quote
So far 3 shops said they wont touch it. I even sent a message to Fiero Motive in Northern Florida with no response. The phone number does not go through either.



Perhaps reach out to PFF members in Florida like 82-T/A who might suggest a shop....?