I repaired mine and added a cover, this is the prototype and I used grey stitching to show the stitching contrast. Final cover will be ready tomorrow and added to the other products I make
Comments, Suggestions? Russ
[This message has been edited by Russ88TTop (edited 07-28-2011).]
IP: Logged
09:54 PM
PFF
System Bot
TXGOOD Member
Posts: 5410 From: Austin, Texas Registered: Feb 2006
Mike, donnie, Will - Thanks OneSlow - I repaired the bottom of the surround first to take out the bow and the way the cover is made it helps to bring the top close to the original alignment F84 - yea, I'll work on that Herc - It's and overlay psyco - ready for production zefferk - same price and I need the cores
Which brings us to the price. I will need your core and I'll repair as much as possible before adding the cover. The cost is $45 shipped back to you in the US ( Canada will be slightly higher ). As an introduction for a short time, I'll add a matching shifter boot for $15
Color is not limited to Black and material is not limited to C/F, however some materials may be slightly higher
Thanks for looking
Russ
IP: Logged
11:47 AM
Aug 2nd, 2011
87GT2M6 Member
Posts: 1297 From: Miami, Florida The Sunshine State Registered: Jan 2008
As one of Russ’s primary distributors he has shared the latest R&D innovation for our Fieros with me that will blow you away and leave you drooling . These new products are just around the corner. Sorry to keep you in suspense but I just couldn’t help giving everyone a heads up. You guys are going to love this!!!
IP: Logged
04:06 AM
hammer18 Member
Posts: 383 From: Maplewood Minnesota Registered: Jun 2007
Really cool stuff!!!!! I think a speaker wrap or cover to tie the dash into some of your products would be a home-run ! Or maybe an applique to go in the recess of the door behind the armrest.Your innovative products sure give our old cars a fresh new look.Kudos!!
IP: Logged
06:28 PM
Sep 2nd, 2011
infinitewill Member
Posts: 2327 From: Overland Park, KS U.S.A. Registered: Mar 2009
Russ, if you covered the rest of the center console (eg: the center armrest) I think you could make a fortune. I would be in for one. I sent you a PM as I am interested in buying on you your surrounds
Dr. W
------------------ Is your Fastback GT's trunk seal shot? My Gen III replacement GT trunk seals with solid molded corners are now in production. $95 + $15 flat rate shipping to the US (contact me for international shipping rates) or buy two and pay only a single shipping rate! More info can be found here GT Trunk Seal Project
Which brings us to the price. I will need your core and I'll repair as much as possible before adding the cover. The cost is $45 shipped back to you in the US ( Canada will be slightly higher ). As an introduction for a short time, I'll add a matching shifter boot for $15
Color is not limited to Black and material is not limited to C/F, however some materials may be slightly higher
Thanks for looking
Russ
Russ, I would like a shifter surround cover made. How much is it for the Carbon Fiber or dark gray? How long is the turn around time?
Thanks, Joe
[This message has been edited by Joe 1320 (edited 09-03-2011).]
IP: Logged
11:38 AM
infinitewill Member
Posts: 2327 From: Overland Park, KS U.S.A. Registered: Mar 2009
Joe - still holding at $45 + special $15 for shifter boot Will - got it - thank you, Oldrock - PM replyed to, no problem foxy - I thought everyone was broke in this economy, but I'll be here when your ready
Finished this one in Black C/F with Red stitching and a shifter boot and mirror covers to match. I have a few more projects to complete for him before shipping.
Finished the HVAC and Gauge Surround in Black Carbon Fiber Vinyl to go with the shifter surround. The stitchng is actually Bright Red and the faceplates are not tighten down
Russ
IP: Logged
01:16 PM
PFF
System Bot
donnie072003 Member
Posts: 1956 From: LaSalle, IL. Registered: Feb 2010
Russ, I wan't throw an idea your way. Feel free to tell me it's a dumb idea. How would your surround look covered in the charcoal suede headliner material?
------------------ Peace!!
B2 OUT!! 86GT 3.4LProject
IP: Logged
09:41 PM
Oct 16th, 2011
Russ88TTop Member
Posts: 805 From: Denver, IN, USA Registered: Jul 2004
could these last 20+ years without warping or peeling like the stock stuff has? i really really like al the work youve done! but i havent seen anything for the center console/glove box yet. might not have opened the page that would contain it, unless you havent made one yet... you should