 
     |
| Sunroof tracks Stainless and powder coated mild steel (Page 7/28) |
|
NOVAFIERO
|
MAY 07, 08:47 AM
|
|
|
I'll take a stainless set too. Canada B4G 1B4
|
|
|
|
Driver_WT
|
MAY 07, 01:02 PM
|
|
Have the sets for the first list been shipped yet?
Thanks.
Wade
| quote | Originally posted by silver 85 sc:
Here's the list.
set # member
1 LFiero67
2 Driver_WT
3 DJErikd
4 Fieromaster88
5 QuadGT
6 fieroseblack
7 flimbob
Rich
|
|
------------------
1984 Fiero, Black notchback, 355 SBC, 4 speed
|
|
|
|
silver 85 sc
|
MAY 07, 10:18 PM
|
|
| quote | Originally posted by Driver_WT:
Have the sets for the first list been shipped yet?
Thanks.
Wade
|
|
Everything from the first batch has been shipped.
Rich
|
|
|
|
LFiero67
|
MAY 08, 09:56 PM
|
|
|
Got mine today. They look great, and fast shipping! Thanks, can't wait to install. ------------------
11.425 @115.60
Best 60' 1.543 seconds
3800 S/C 4T65E
New combo : Billet 6262 Precision turbo, PT1001 intercooler, ST1 cam, 130lb springs, comp pushrods, HV3, otherwise stock L36.
|
|
|
|
silver 85 sc
|
MAY 08, 10:32 PM
|
|
Material shows up tomorrow for round 2. If my nesting is correct I will get 30 sets out of this run.
Rich
|
|
|
|
fieroseblack
|
MAY 09, 03:47 PM
|
|
Got mine today, look GREAT! Am I correct that the headliner must come down to install. I have The Fiero Store ABS covered type, with a sun roof. I wasn’t sure if I could get to the studs without removing the headliner or could I reach them with the sun roof trim piece removed.
Thanks
Mike Parker
|
|
|
|
silver 85 sc
|
MAY 09, 10:40 PM
|
|
| quote | Originally posted by fieroseblack:
Got mine today, look GREAT! Am I correct that the headliner must come down to install. I have The Fiero Store ABS covered type, with a sun roof. I wasn’t sure if I could get to the studs without removing the headliner or could I reach them with the sun roof trim piece removed.
Thanks
Mike Parker |
|
I am not sure. I have my '84 that is now waiting for a set and I will find out. My '86 doesn't have a headliner. Although it looks like the studs are pretty close to the edge.
Rich
P.S. I have material!!!
|
|
|
|
BMTFIERO
|
MAY 10, 05:53 PM
|
|
Put me down for a set of stainless?
PM me with paypal info. (shipping to Beaumont, TX 77707
|
|
|
|
silver 85 sc
|
MAY 10, 08:28 PM
|
|
| quote | Originally posted by BMTFIERO:
Put me down for a set of stainless?
PM me with paypal info. (shipping to Beaumont, TX 77707 |
|
Your on the list
Rich
|
|
|
|
ly41181
|
MAY 10, 10:43 PM
|
|
| quote | Originally posted by silver 85 sc:
Just a note, I installed mine without removing the roof panel. I will get a picture of the tool I made to get the rivet washers installed under the roof panel then all you will need to install these are a putty knife, 1/8" drill bit, rivet gun, a 10mm socket and ratchet, and the gasket adhesive. Of course if you decide to glue/tape these in you will need the putty knife, gasket adhesive, rivet gun, and the10mm socket and ratchet.
Rich |
|
Hi! I was wondering if you had that picture of the tool you made. Is there anything special needed to make it?
Josh
|
|
|
|