 
     |
| Project Genisis Lo Budget 3800SC (Page 37/42) |
|
Koert
|
MAY 07, 08:01 PM
|
|
|
Awesome threat! Did you get those red lights on there? They will look so awesome! I need to see it man
|
|
|
|
hercimer01
|
MAY 09, 01:58 AM
|
|
Thanks!
I did get just the low beams wired up and working so I can drive it. I still need to put a finish on the buckets and run a power feeder from the battery to the front so I can finish wiring the high beams.
I figured out a way to do either white or red in the same halo. I will do that when the buckets are done.
My Fuel pump quit working due to corroded terminals in the pump connector, I had to drop the tank again and rewire the pump. This time I soldered 10AWG wire directly onto the terminal lugs of the pump.
One thing at a time.
|
|
|
|
Koert
|
MAY 10, 08:45 PM
|
|
|
That's awesome. You take a car make it awesome, look at it and think "hmm this can be better" And actually make it even better
|
|
|
|
hercimer01
|
MAY 27, 01:48 AM
|
|
I have had to finish the battery relocation before i can finish wiring the high beams. This is my progress so far.
I found this some where on the web.
|
|
|
|
hercimer01
|
MAY 30, 01:49 AM
|
|
|
|
|
hercimer01
|
MAY 30, 06:11 PM
|
|
Final installation.
|
|
|
|
ltlfrari
|
JUN 18, 08:24 AM
|
|
| quote | Originally posted by hercimer01:
I have had to finish the battery relocation before i can finish wiring the high beams. This is my progress so far.
I found this some where on the web.
|
|
That somewhere would be me!
I also weld a short length of rod to the front of the box, just above the floor so that the lip on the base of the battery fits under it. That stops the battery from tipping backwards and the clamp holds the back down.
I stick a sheet of thin plastic (something like the stuff a skylight might be made out of) to the front face where the battery slides in and glue a short length of PVC pipe (about a quarter inch long) into the holes so that the battery terminals cannot touch bare metal.[This message has been edited by ltlfrari (edited 06-18-2015).]
|
|
|
|
hercimer01
|
JUN 23, 11:36 PM
|
|
| quote | Originally posted by ltlfrari:
That somewhere would be me!
I also weld a short length of rod to the front of the box, just above the floor so that the lip on the base of the battery fits under it. That stops the battery from tipping backwards and the clamp holds the back down.
I stick a sheet of thin plastic (something like the stuff a skylight might be made out of) to the front face where the battery slides in and glue a short length of PVC pipe (about a quarter inch long) into the holes so that the battery terminals cannot touch bare metal.
|
|
Thanks! I was afraid about posting other peoples stuff. I'm glad you like it. By under the front of the box you mean, forward, I bolted in a bent L channel across the top of the battery to hold it down. The clamp, I welded a nut to the bottom of the box to secure the back of the battery. I like the idea of the plastic sheet. However I am concerned with the width of the battery in the tray. It's about 1/2 inch wider than the battery. I'm trying to figure out what do to keep it from sliding sideways. Any ideas?
|
|
|
|
hercimer01
|
JUL 20, 12:24 AM
|
|
Slow going but I'm working on it. Still gotta connect the starter and ground after I disconnect the battery of course.
 [This message has been edited by hercimer01 (edited 07-20-2015).]
|
|
|
|
hercimer01
|
JUL 24, 07:30 PM
|
|
I learned how to TIG weld today!
|
|
|
