 
     |
| FieroGT stretch Concept (Page 13/240) |
|
Amida
|
APR 09, 11:54 AM
|
|
|
Put it into your 3D modeller & see how it looks.
|
|
|
|
Jake_Dragon
|
APR 09, 12:02 PM
|
|
| quote | | Originally posted by Amida: Bob, Yes there's not much left of the Fiero in that last one, but I did try to design around the stock door glass. This next one I played off of your Bonneville theme. More mods needed for this one...changes to hood, wider fenders, headlights, framing. But, there's still a Fiero beneath it.
Amida 
|
|
I like that, I was thinking about raising the front of the hood about 1 inch and doing something just like that.
|
|
|
|
Amida
|
APR 09, 12:04 PM
|
|
|
Jake, why do you have to raise the hood, to clear the head lights? [This message has been edited by Amida (edited 04-09-2006).]
|
|
|
|
Custom2M4
|
APR 09, 12:15 PM
|
|
|
so the headlights will but up higher. However you can just cut into the hood, install the scoops, and the headlights IN the hood. Raise them how you must, have the fiero hood raise like it normally does, leaving the headlights behind, but taking the scoop with it. Could be a nice project. I'll be using sunfire lights in mine when I get to it though.
|
|
|
|
Gokart Mozart
|
APR 09, 03:20 PM
|
|
| quote | | Originally posted by Custom2M4: so the headlights will but up higher. However you can just cut into the hood, install the scoops, and the headlights IN the hood. Raise them how you must, have the fiero hood raise like it normally does, leaving the headlights behind, but taking the scoop with it. Could be a nice project. I'll be using sunfire lights in mine when I get to it though. |
|
Follow the original lines. Leave the center part stock height but where the headlights go raise that part and make it flow with the headlights. Man, I wish I had PS to show you what I mean.
|
|
|
|
RCR
|
APR 09, 07:39 PM
|
|
| quote | | Put it into your 3D modeller & see how it looks |
|
Geez, you make it sound easy...  If I were better at it, it probably would be. Bob
|
|
|
|
Amida
|
APR 13, 12:10 PM
|
|
|
Bob, you make it look easy to do. A slight variation on the hood venting: 
I'll try fitting the 300zx headlights next. Being lower profile, they may not require raising the front side of the hood like the Bonneville lights would. [This message has been edited by Amida (edited 04-13-2006).]
|
|
|
|
Custom2M4
|
APR 13, 03:22 PM
|
|
|
Just make sure you take the width of the 300zx lights into consideration... They are pretty dang wide... I'd say about 25 inches..
|
|
|
|
Jake_Dragon
|
APR 13, 04:22 PM
|
|
| quote | | Originally posted by Amida: Jake, why do you have to raise the hood, to clear the head lights? |
|
Yes, It could probably be done without raising the hood but I'm thinking of adding some other things there as well.
|
|
|
|
Amida
|
APR 14, 02:09 PM
|
|
|
Here is the Fiero with 300zx headlights, fender flares and aero fascia with extended lower lip. The lower profile of the lights should fit in pretty well with the slope of the Fiero hood. 
|
|
|
|