
 |
| Exhaust manifold bolt leaking coolant (Page 1/2) |
|
mtgjudge
|
AUG 30, 08:25 AM
|
|
Hey folks,
I asked about this on PFF about 20 years ago, but I cannot find the thread. Anyways, back in the day I replaced my exhaust manifold, and like many have experienced, a few of the bolts were seized and the heads snapped off, so I had to drill out and helicoil a few. On the last bolt, I drilled through the water jacket, and created a tiny coolant leak that drips when the engine is running. I lived with it until I withdrew my car from use about 8 years ago. As you may infer from my recent forum activity, the car is going back on the road. This annoying drip is on the punch list. I know one solution is to remove the top end and take it to a machinist to weld. I'm obviously looking for something much less involved. Thanks in advance!------------------ Wesley Williams 1986 GT
|
|
|
Vintage-Nut
|
AUG 30, 12:01 PM
|
|
| quote | | I asked about this on PFF about 20 years ago, but I cannot find the thread. |
|
You'll never guess what I did... by mtgjudge https://www.fiero.nl/forum/...050119-2-055755.html
| quote | | I know one solution is to remove the top end and take it to a machinist to weld. I'm obviously looking for something much less involved. |
|
How many miles are on the valves?
IMHO - Perhaps removing the heads and getting a fresh valve job can 'kill two birds with one stone'.
AND if you ported the exhaust manifolds, why not port the intake manifolds too? 
------------------ Original Owner of a Silver '88 GT Six-Year 'Refurbishment' Nearly Finished...
|
|
|
mtgjudge
|
AUG 30, 02:38 PM
|
|
| quote | Originally posted by Vintage-Nut:
How many miles are on the valves?
IMHO - Perhaps removing the heads and getting a fresh valve job can 'kill two birds with one stone'.
AND if you ported the exhaust manifolds, why not port the intake manifolds too? 
|
|
Thanks for finding the thread. As I stated, I'm not keen on the "project creep" of disassembling the top end and removing the head to spot weld it. I'm hoping for a simpler fix. The best alternative in the old thread was high temp RTV. Has anyone tried that and been successful with an application with a helicoil? I'm interested in knowing if there have been tech or improvements to best practices in the last 22 years that may provide me with other options. ------------------ Wesley Williams 1986 GT
|
|
|
Vintage-Nut
|
AUG 30, 04:24 PM
|
|
|
If you want an 'unconventional' repair, I will go with a permanent bond like J-B Weld Water Weld Epoxy Putty Stick than High Temp RTV...
|
|
|
mtgjudge
|
AUG 30, 04:33 PM
|
|
| quote | Originally posted by Vintage-Nut:
If you want an 'unconventional' repair, I will go with a permanent bond like J-B Weld Water Weld Epoxy Putty Stick than High Temp RTV... |
|
Perhaps I will do both out of an abundance of caution. Do you think the JB Weld will maintain its bond over the repeated thermal expansion and contraction of the head?
------------------ Wesley Williams 1986 GT
|
|
|
Vintage-Nut
|
AUG 30, 05:05 PM
|
|
I plugged 'holes' in motorcycle cases with the original J-B Weld which withstands temperatures up to 550°F and never leaked oil....
J-B Weld ExtremeHeat is one of their highest temperature products at 1,000°F https://www.jbweld.com/product/j-b-extremeheat
|
|
|
mtgjudge
|
AUG 30, 05:32 PM
|
|
| quote | Originally posted by Vintage-Nut:
I plugged 'holes' in motorcycle cases with the original J-B Weld which withstands temperatures up to 550°F and never leaked oil....
J-B Weld ExtremeHeat is one of their highest temperature products at 1,000°F https://www.jbweld.com/product/j-b-extremeheat |
|
That's nuts. (See what I did, there?) I was going to use the marine weld because of contact with the coolant. Says it can withstand 500 F. Whateya think?
------------------ Wesley Williams 1986 GT
|
|
|
Raydar
|
AUG 30, 08:10 PM
|
|
These heads are everywhere, and cheap. All of the iron head 60 degree engines with EFI have the "big" valves - to include the TBI S10s and Sonomas. There should be zillions of them. I think I'd just replace it - especially if you're going to do a valve job, anyway. I think Rockauto even has them. I know they did, at one time.
Edit - Not on Rockauto anymore. At least not under "Fiero".[This message has been edited by Raydar (edited 08-30-2026).]
|
|
|
fierofool
|
AUG 31, 07:11 PM
|
|
|
Rock auto has 94 Camaro 3.4 heads @$381. Same head as the Fiero.
|
|
|
Vintage-Nut
|
AUG 31, 08:12 PM
|
|
The OP has been clear; he has no desire to remove the cylinder head.
He wants an 'easy' fix that requires the minimal effort.
*Plug the coolant hole and hope for the best...
|
|

 |