

 |
| Tcc 3rd gear switch (Page 1/1) |
|
Fierogary
|
AUG 15, 12:39 AM
|
|
In regards to the 3rd gear switch on a 86 fiero gt automatic: there are two wires that attach to the swich- one black and one white. Does it matter which pin these wires connect to? Most grateful for any information.
|
|
|
Dennis LaGrua
|
AUG 15, 02:10 AM
|
|
|
You may be talking about the transmission torque converter lock up switch. I have read mixed opinions on this some say proper polarity is necessary while others say it's not. My opinion is that proper polarity is necessary. ------------------ " THE BLACK PARALYZER" -87GT 3800SC Series III engine, custom ZZP /Frozen Boost Intercooler setup, 3.4" Pulley, Northstar TB, LS1 MAF, 3" Spintech/Hedman Exhaust, P-log Manifold, Autolite 104's, MSD wires, Custom CAI, 4T65eHD w. custom axles, Champion Radiator, S10 Brake Booster, HP Tuners VCM Suite. "THE COLUSSUS" 87GT - ALL OUT 3.4L Turbocharged engine, Garrett Hybrid Turbo, MSD ign., modified TH125H " ON THE LOOSE WITHOUT THE JUICE "
|
|
|
Fierogary
|
AUG 15, 11:09 AM
|
|
I agree with you on the polarity. That is my concern. How do I find info on polarity connections?
|
|
|
Vintage-Nut
|
AUG 15, 11:16 AM
|
|
|
Do You Have the Pontiac Fiero Service Manual? ------------------ Original Owner of a Silver '88 GT Six-Year 'Refurbishment' Nearly Finished...
|
|
|
Fierogary
|
AUG 15, 09:31 PM
|
|
|
Yes- have the original service - will look up again to see if I missed something here.
|
|
|
Vintage-Nut
|
AUG 15, 11:45 PM
|
|
I found the TCC solenoid wiring diagram but didn't find the pressure/ 3rd gear switch wiring diagram....
PS - Found a thread which says "Nope, doesn't matter..."
Question for those who have replaced their TCC and pressure switch... https://www.fiero.nl/forum/...110502-2-105022.html[This message has been edited by Vintage-Nut (edited 08-16-2026).]
|
|
|
fieroguru
|
AUG 16, 10:14 AM
|
|
The pressure switch just connects 2 terminals to provide an electrical pass through connection, so polarity doesn't matter.
|
|
|
Dennis LaGrua
|
AUG 16, 04:41 PM
|
|
| quote | Originally posted by fieroguru:
The pressure switch just connects 2 terminals to provide an electrical pass through connection, so polarity doesn't matter.
|
|
Since the torque converter lockup switch is also connected to the brake switch circuit my concern was that polarity would be necessary but perhaps as you claim it doesn't matter.------------------ " THE BLACK PARALYZER" -87GT 3800SC Series III engine, custom ZZP /Frozen Boost Intercooler setup, 3.4" Pulley, Northstar TB, LS1 MAF, 3" Spintech/Hedman Exhaust, P-log Manifold, Autolite 104's, MSD wires, Custom CAI, 4T65eHD w. custom axles, Champion Radiator, S10 Brake Booster, HP Tuners VCM Suite. "THE COLUSSUS" 87GT - ALL OUT 3.4L Turbocharged engine, Garrett Hybrid Turbo, MSD ign., modified TH125H " ON THE LOOSE WITHOUT THE JUICE "
|
|
|
Fierogary
|
AUG 17, 12:14 AM
|
|
Thanx everyone for there input on this matter. Wasn't sure in regards to this polarity issue. In this case it doesn't matter which wire connects to the pins. Always best to ask for advice if not 100% sure!
|
|

 |
|