

 |
| Engine compartment pressure washing (Page 1/2) |
|
mtgjudge
|
AUG 12, 05:08 PM
|
|
Hey folks, what product (i.e. fluid) do you use for washing the engine and compartment? And which components should I waterproof in preparation?
Thank you in advance!
|
|
|
Dennis LaGrua
|
AUG 12, 07:50 PM
|
|
|
I would not use a pressure washer. My technique is to use a sponge with detergent and a roll of paper towels to wipe everything. If you must wet use a low pressure hose. This will avoid getting water in the alternator, distributor, wiring harness and connectors. ------------------ " THE BLACK PARALYZER" -87GT 3800SC Series III engine, custom ZZP /Frozen Boost Intercooler setup, 3.4" Pulley, Northstar TB, LS1 MAF, 3" Spintech/Hedman Exhaust, P-log Manifold, Autolite 104's, MSD wires, Custom CAI, 4T65eHD w. custom axles, Champion Radiator, S10 Brake Booster, HP Tuners VCM Suite. "THE COLUSSUS" 87GT - ALL OUT 3.4L Turbocharged engine, Garrett Hybrid Turbo, MSD ign., modified TH125H " ON THE LOOSE WITHOUT THE JUICE "
|
|
|
82-T/A [At Work]
|
AUG 12, 08:57 PM
|
|
Yeah, like Dennis said... I would not use a pressure washer. That can cut through plastic wiring and other sensitive parts. I'd spray it with engine degreaser, let it sit for a while, and then spray it with a garden hose attachment... one of the garden hose attachments where they pretend like you have a pressure washer, but don't.
Like one of these: https://www.walmart.com/ip/...es-Nozzl/19946509731
|
|
|
Raydar
|
AUG 12, 09:25 PM
|
|
Be careful of cleaning fluids. One of my go-to's is Mean Green, but be very careful. It will oxidize bare aluminum, and "chrome" thermal coatings. It's great for door jambs, and etc.[This message has been edited by Raydar (edited 08-12-2026).]
|
|
|
Vintage-Nut
|
AUG 12, 09:32 PM
|
|

Some members will tell you that they pressure wash their engine, but I don't.
I always clean the engine bay when it is 'cold' - never hot.
To avoid electrical issues as mentioned, cover the distributor/coil and the alternator before spraying anything
Avoid spraying water directly on the top end, the harness and any painted parts; I use low‑flow only
If the block/transaxle are very greasy, use a foaming product and allow the degreaser to soak through the grime; use a brush where you can
Then use higher pressure on the bottom end only to rinse them off
I end with compressed air before starting the engine, and then drive it to the normal operating temperature....
As for:
| quote | | what product (i.e. fluid) do you use for washing the engine and compartment? |
|
I found a product in the 1980's to keep my motorcycles very clean called S100 Total Cycle Cleaner
I was buying it in the 5-liter canisters and yes, I still use it today on my Fiero... 
------------------ Original Owner of a Silver '88 GT Six-Year 'Refurbishment' Nearly Finished...[This message has been edited by Vintage-Nut (edited 08-12-2026).]
|
|
|
Stingray92
|
AUG 12, 10:48 PM
|
|
|
Bad Idea, that's all folks
|
|
|
fieroguru
|
AUG 13, 06:50 AM
|
|
I will provide a differing opinion... I pressure wash mine all the time. Every 2-3 weeks and often daily on the HRPT.
Roll into a car wash, power wash, power rinse and drive away.
I consider it a diagnostic tool. If water causes an issue, investigate the component/connector and address it.
|
|
|
mtgjudge
|
AUG 13, 07:26 AM
|
|
Thanks to everyone for weighing in.
| quote | Originally posted by Vintage-Nut:
As for: I found a product in the 1980's to keep my motorcycles very clean called S100 Total Cycle Cleaner
I was buying it in the 5-liter canisters and yes, I still use it today on my Fiero... 
|
|
This is hyterical. I have a gallon of this that's been sitting around for years. I've long since sold my motorcycle but it did an amazing job on it. Literally in the last two weeks I was trying to think of someone whom I could give this away to because I was sick of looking at it. Now I have a use for it!
|
|
|
Raydar
|
AUG 13, 09:41 AM
|
|
| quote | Originally posted by fieroguru:
I will provide a differing opinion... I pressure wash mine all the time. Every 2-3 weeks and often daily on the HRPT.
Roll into a car wash, power wash, power rinse and drive away.
I consider it a diagnostic tool. If water causes an issue, investigate the component/connector and address it.
|
|
I actually like this line of thought. I try to be careful when I wet my engine down, but the connectors are designed to be waterproof, so... I have to believe they called them "weather pack" for a reason.
|
|
|
Vintage-Nut
|
AUG 13, 10:14 AM
|
|
| quote | Originally posted by mtgjudge:
This is hyterical. I have a gallon of this {S100} that's been sitting around for years. / Now I have a use for it! |
|
Excellent! Yes, S100 really works an "amazing job" and isn't 'cheap'.
I use it on any 'oily' jobs, like cleaning my coffee bean containers or the stove hood vent filters!
|
|

 |
|