

 |
| Original R-12 A/C (Page 1/2) |
|
Project Pegasus
|
JUL 27, 11:45 AM
|
|
I just acquired a pretty mint 87 GT with 54K miles. I drove it home 2,100 miles and it dove perfectly. Mint but aged. I think the A/C equipment is all good but in need of seals and service. I'd like to keep the original R-12 but most people seem to think it is impossible. I'm in Utah. Does any one know who could service the A/C within a reasonable distance? Any tips or directions would be helpful. Thanks in advance.
|
|
|
Raydar
|
JUL 27, 11:52 AM
|
|
I think that you'll find that the sale of R-12 is completely illegal. What you'll probably end up with, at best, is some sort of hydrocarbon (petroleum based) refrigerant, with cooling properties similar to R-12. Some will say that flammable refrigerant is dangerous, but unless I'm completely mistaken, the most recent 1234-YF refrigerant is, in fact, flammable. Probably much easier to do an R-134 conversion while that is still available.
If someone knows different, please jump in.[This message has been edited by Raydar (edited 07-27-2026).]
|
|
|
Project Pegasus
|
JUL 27, 12:25 PM
|
|
|
Thanks for your comment, but this is the problem I'm running into, it is NOT illegal and is readily available. I'm just looking for the guys or guy that works on these old systems. It's only illegal for manufacturers to use them on new cars, it's perfectly ok to service and fill the old R12 systems.
|
|
|
Vintage-Nut
|
JUL 27, 02:42 PM
|
|
To ME: I believe it requires a full proper clean, plus a refrigerant conversion
1st is the Regulatory Milestones: * 1992 Ban: The use of R-12 in new vehicles and appliances was prohibited in the U.S. This was the beginning of the end for R-12. * 1994 Production and Import Ban: The production and import of R-12 was officially banned, though some refrigerant was still available from recycled sources. * 2010 Total Phase-out: By 2010, the availability of R-12 had significantly diminished, as manufacturers had stopped producing it.
So, IF you find a shop who will service the Fiero A/C, my bet is that it won't be R-12.
2nd is the majority of PFF members who serviced their A/C have the skills/tools to properly service the system as DYI, not 'a shop'.
3rd is the cost, DYI is around $1,000; prepare for a $2,000 bill or more IF you find 'a shop'.
In 2024, I asked a similar question:
| quote | | What can an 'average' Fiero owner prepare before finding an A/C shop to clean/flush/evacuate/test/pressure the system with R-134A refrigerant? |
|
The Answer:
| quote | If you can actually find a A/C shop willing to work on a Fiero, I would expect them to charge $2000+ to get the system operational at current shop rates, VS probably under $1000 to do it yourself.
|
|
As a DYI with special knowledge and experience:
$200 compressor $45 accumulator $5 orifice tube $75 switches $20 HNBR o-rings $20 R-134A conversion fittings $50 gauge set $100 vacuum pump $30 for 3 cans of R-134A $15 refrigerant oil $30 A/C flush solvent $30 flush bottle
Plus, other odds and ends
I decide it is a complicated topic to resurrect a long-dead R12 air conditioning system and isn't for beginner DIYers to just blinding jump in nor found a A/C shop who will work on a Fiero...
Good Luck on your quest!
PS - For Your Enjoyment: Proper Air Conditioning System Servicing and Retrofitting to R-134a https://fierofocus.com/Tech...tem_retrofitting.pdf
------------------ Original Owner of a Silver '88 GT Six-Year 'Refurbishment' Nearly Finished...[This message has been edited by Vintage-Nut (edited 07-27-2026).]
|
|
|
82-T/A [At Work]
|
JUL 27, 03:29 PM
|
|
It's not illegal per-se, but normal people cannot buy it. You have to have a license to be able to purchase it legally. I have such a license, all I had to do was take a test online to verify that I knew the proper procedure for handling it. Basically, a long-ass test for me to promise and understand that I shouldn't just discharge R-12 into the atmosphere.
I'm not aware of anyone who recharges R12 systems for cars. Again, just being honest, but it's not ideal. Your system leaked / stopped working for a reason, and in order for it to operate properly, you probably need to replace all the seals anyway. I am not even sure if you can still get R12 with a sealing agent in it.
Most A/C places will have R12 stored off that they've captured. It was also used in HVAC systems as well, so they will have it. You'll want to have your car fixed first (find out why the A/C stopped working, fix it, flush it), and then take it to an MVAC shop and have them vacuum it, and then charge it.
|
|
|
Project Pegasus
|
JUL 27, 09:26 PM
|
|
|
I can't even use the pressure gages to check the pressure of the system because the R12 adapters are different (I need the adapters). It's looking more likely that I'll have to fold and get it converted. It's funny because I am not licensed but I know a few sources to get R12. I guess it wouldn't be an illegal transaction though because I'm not certified (I didn't pass the test). I know of people that still work on classic cars with the original R12 in New Jersey, Alabama, Texas etc., I would like to find someone closer though.
|
|
|
82-T/A [At Work]
|
JUL 28, 07:49 AM
|
|
| quote | Originally posted by Project Pegasus:
I can't even use the pressure gages to check the pressure of the system because the R12 adapters are different (I need the adapters). It's looking more likely that I'll have to fold and get it converted. It's funny because I am not licensed but I know a few sources to get R12. I guess it wouldn't be an illegal transaction though because I'm not certified (I didn't pass the test). I know of people that still work on classic cars with the original R12 in New Jersey, Alabama, Texas etc., I would like to find someone closer though. |
|
It would be illegal for the person who sells it to you, as it's only meant for EPA-certified technicians... not illegal for the person who buys it. It was amended to the Federal Clean Air Act back in 1990, and took effect in 1992. Basically outlawed all R12. The punishment is defined by the EPA (from what I remember), and it's typically a fine.
If you look on eBay, there are a bunch of companies selling the "Arctic-Blast" / Envirosafe R12 refrigerant. It's all new stuff. They don't seem to be asking for an EPA number, and many of them come with the proper connector and hose that you need to fill your car.
The thing I wanted to emphasize last time though is that your system is now ~40 years old. All those O-Rings are going to be failing. Whether you want to keep R12 or convert to something else, I'd recommend replacing the O-Rings again. You can still get all the new R12 O-Rings, they are the standard NBR Nitrile Rubber (black) O-Rings. You do not want to use the ones for R134 (which are hydrogenated rings).
I'd want to know why your system stopped running though. If your compressor seized, then it likely shot its guts out all through the system, in which case you'll need to flush the entire system and replace the compressor. In my personal opinion, you'd probably also want to replace the condenser... they sell new ones for pretty inexpensive, and they work well. There are a LOT of O-rings, unfortunately, since the lines run the length of the car to the compressor and back.
I don't know how comfortable you are working on cars. MVAC stuff isn't hard, it really isn't... but there's a lot there to replace the rings and / or upgrade. I just don't trust most shops, to be honest... I just don't. I'd rather spend $1,000 bucks getting everything I needed and do it myself, than paying a shop $600 to do it for me.
|
|
|
Project Pegasus
|
JUL 28, 09:57 AM
|
|
I feel the same way about "trusting" shops, especially with a car they are not familiar with like a Fiero. I have a friend with a DeLorean and he simply uses the specialty shop in California and Seattle Washington because he doesn't trust anyone else. I'm surprised that there aren't a few of those shops around for Fiero out west.
I ordered some adapters for the gauges to connect to the R12 system so I can start with a pressure test. The car was garaged for most of its life so I would guess that the lack of use is the real problem. I don't think the compressor went bad but I would assume that the seals and o-rings are shot. I'll do a pressure test and see what I've got, then I'll start replacing o-rings.
Thanks for the info on Arctic Breeze and the laws for acquiring R12.
|
|
|
Larryinkc
|
JUL 28, 11:18 AM
|
|
Here's some info on using R152a, some will say don't use it. A quick Google search will get lots of info on using it. I have had it in my Mera AC for 9 years with no adverse effects. I flushed the complete system and ended up with a new condenser due to a leak. I initially used ester oil and the compressor got real noisy after the first summer. I flushed the system again, installed a new Denso compressor and used PAG oil this time, which is the Denso recommended oil. The system has been good since then. I get 40 degree air out the side vents at a little over idle without an fan blowing on the condenser.
I live in Kansas City elevation 900' and ended up using a yellow orifice tube with the R152a charge.
https://www.fiero.nl/forum/Forum2/HTML/138319.html[This message has been edited by Larryinkc (edited 07-28-2026).]
|
|
|
82-T/A [At Work]
|
JUL 28, 01:54 PM
|
|
| quote | Originally posted by Project Pegasus:
I feel the same way about "trusting" shops, especially with a car they are not familiar with like a Fiero. I have a friend with a DeLorean and he simply uses the specialty shop in California and Seattle Washington because he doesn't trust anyone else. I'm surprised that there aren't a few of those shops around for Fiero out west.
I ordered some adapters for the gauges to connect to the R12 system so I can start with a pressure test. The car was garaged for most of its life so I would guess that the lack of use is the real problem. I don't think the compressor went bad but I would assume that the seals and o-rings are shot. I'll do a pressure test and see what I've got, then I'll start replacing o-rings.
Thanks for the info on Arctic Breeze and the laws for acquiring R12. |
|
There is West Coast Fiero, but they're out in California.
Also, when doing all this stuff, there are different expansion valves (basically the little cartridge filter thingy that installs in the orifice tube). There are three different kinds... for the life of me I cannot remember. I'm MVAC certified, but I never said I was any good at it! Haha... but the expansion valve that fits into the orifice tube usually comes in three colors. You'll want to replace this regardless, as well as the "dryer" (which is the steel looking cyl). The cyl has dessicant in it, and it's meant to dry the freon / gas and eliminate any water. They're cheap, like $30 bucks, so you'll want to replace it. Don't remove the caps until you're ready to install it.
But again on the expansion valve... there are three colors, I don't remember which does what, but they are rated for different atmosphere levels. So if you're like a couple thousand feet above sea level, you'll want to swap it out. Generally speaking, cars come with the one in the middle (whichever color that is). There's a brown/red, a blue, and a white one... I can't remember. In any case you can make the A/C colder by going with whichever one allows more freon through the valve (blue one maybe)? But that's another thing you'll want to have replaced when you do the work. They're like $7-10 bucks.
|
|

 |
|