Intermittent Code 55 headache over for a year now (Page 1/3)
fierosound JUN 24, 07:45 PM
This is with the 87 GT with 3.4L S/C running a 1227165 ECM
(functionally the same a stock and been working fine for 12 years).
Any ideas you have for problems for a stock Fiero ECM will relate.

I've been chasing this problem for over a year.
Most of the time I do NOT get any codes.
I've had a Code 55 before, and another one today.

Code 55 ECM Failure
Check all ground connections of the ECM. If all are OK, replace ECM.

Very random. Most times there is NO issue with driving and everything works normally.

Until:
Car drives fine. Park and do your business.
Come out to start car, turn key to RUN position - CEL (Check Engine Light) flashes once and goes out.
THAT is not correct. CEL should remain ON until engine starts and runs.
If you start engine now, it stalls after a couple of seconds, over and over. Won't stay running. NOT driveable.

Get towed home intending to trace and fix the problem the next day.
Next day, put the key in and everything is back to normal.
CEL comes on and stays ON until engine starts (as it should).
Car drives normally again - until the next time the problem arises.

I've checked every ground and connection to ECM.
Checked CEL light circuits and found nothing wrong.
Harness grounds that go to head on driver's side below Throttle Body are clean and solid.
I've never found anything that's obviously (aha!) the problem, only hoped I had fixed something.


I finally convinced myself there is no problem WITH the wiring in the car and swapped in a spare ECM on the weekend.
I was thinking the ECM must have had a cold solder joint internally somewhere. Had fingers crossed.

While out on a drive today, had a BIG hiccup - like a giant engine miss - CEL light came on but engine stayed running.
That threw the Code 55. So I guess I'm back to square one. ECM was not the problem.
But the big hiccup was like the ECM had lost all power for half a second.


I should say I've been towed 3 times and 3 times had the problem when planning to leave home (had to leave car).
The issue "went away" after repeated "Key On" trials at least once.
Another time, pulling and reinserting ECM fuse seemed to correct the problem.
Never found the actual problem and issue always seemed to resolve itself while disconnecting/reconnecting things while trying to find the problem.

I think I'll have to look at the back of the Fuse Box to see if there's any connection issue with the ECM fuse circuit.
I suspect a momentary power failure may look like a Code 55 "ground failure" to the ECM. There isn't a "No Power" code.
I'm thinking if it's NOT the ground, it's the "other end" of the circuit - an intermittent cutout on the power input...

Any other ideas guys??


------------------
My World of Wheels Winners (Click on links below)

3.4L Supercharged 87 GT and Super Duty 4 Indy #163

[This message has been edited by fierosound (edited 06-25-2026).]

fierosound JUN 26, 01:47 PM
After rechecking all the wiring to the ECM inside the car, I'm thinking I must
have an intermittent break inside the ground wiring bolted the V6 head.

Sure, it's bolted clean and tight, but the wiring may be compromised.
It's in a nuisance location that's hard to work on, but I think the best
bet at this point is to replace the last foot of wiring on all of them.
Just wanted to add, the wiring on the car looks "strained" - pulled tight by weight of the harness?

[This message has been edited by fierosound (edited 06-28-2026).]

Raydar JUN 27, 01:07 PM
You said you swapped ECMs. I'm guessing that you had to swap your EPROM in, since yours is a custom build. If not, I would check to see if it's seated properly.
Also, as I recall, there is a smaller chip (CALPAK?) also installed in a socket, near the EPROM. Make sure that chip is seated well, too.

When it acts up, does your fuel pump prime?

I could be completely on the wrong track, but at least it's free to check.

[This message has been edited by Raydar (edited 06-27-2026).]

jdv JUN 27, 04:32 PM
How old is the nvram chip? The internal battery might be going or do you have an eprom in that socket?
fierosound JUN 28, 12:41 PM

quote
Originally posted by jdv:

How old is the nvram chip? The internal battery might be going or do you have an eprom in that socket?



I'm using the NVRAM board with it's original chip, not a Memcal/Eprom.
Yes, I've thought about the internal battery, but expect it to be good or dead - not an "in-between".

I have the NVRAM in my Indy as well. I could swap between cars and reprogram them.
Then see if the Code 55 problem "moved" from one car to the other.

[This message has been edited by fierosound (edited 06-28-2026).]

fierosound JUN 29, 05:10 PM
Here's the wiring diagram for ECM grounds that go directly to G503 and G504 on the engine head.






The only thing I can see that is "perhaps" causing an intermittent is the Black and Green wires to G504 .
The Black wire from ECM D1 looks like it's pulling away. Of course, it could have been stretched and is internally frayed or broken.

[This message has been edited by fierosound (edited 06-29-2026).]

jdv JUN 29, 05:33 PM
If you are done tuning your cars if might be a good idea to burn your tune to an eprom to eliminate that variable. I had one of my non delcohacking units give me trouble.
fierosound JUN 29, 05:40 PM

quote
Originally posted by jdv:

If you are done tuning your cars if might be a good idea to burn your tune to an eprom to eliminate that variable. I had one of my non delcohacking units give me trouble.



Maybe. I don't know what's involved.
Haven't inquired as to who can do it properly.
jdv JUN 29, 06:36 PM
It is in the $12p info. I sold my burner when i let my last fiero go. I need to get another one. Chet or Mickey_Moose can do it just need to stack the bin.
fierosound JUL 04, 02:05 PM
Progress. Made new pigtails that I crimped/soldered to the harness.
It was when I was bolting them back to the head, that I discovered one bolt was longer than the other.
This mixup may have happened when I last had things apart to replace the clutch.

I measured the hole depth, and yes, it is possible the bolt was bottoming in the threads.
(this may have been the problem all along - bolt is "tight" but not actually clamping wiring eyelets solidly to head)
I replaced it with a 1/4" shorter bolt to match the other and used star washers.

So far, the car has been driving fine. ECM is not complaining about a "bad ground" anymore.
As I mentioned before, the CEL problem and Code 55 was very random.
But I am confident it is solved now. (fingers crossed).
(2 of the 4 wires are grounds directly to the ECMs internals)




[This message has been edited by fierosound (edited 07-06-2026).]