

 |
| I can't keep my engine running long enough to set timing! (Page 1/2) |
|
Darthscooby1001
|
JUN 22, 12:34 PM
|
|
I can't keep my engine running long enough to set timing!
I have been renovating my 86 GT for the past two years. After the engine was rebuilt, replacing almost everything, the first turn of the key was an anti-climax leading me to change the fuel pump, which had subsequently died whilst I worked elsewhere on the car. However, I had a spare, albeit an old one, which appeared to work fine and the motor fired and allowed me to run it for 20 minutes with the break-in oil and copious amount of assembly lube. After draining said break-in oil and having a heart attack seeing a resemblance of strawberry milk running out the drain plug, I remembered the purple lube and red oil that had been in there! I refilled with fresh oil and moved on to other areas of my renovation. I turned the car over and periodically checked the dip stick several times and it remained golden coloured with clean oil, no contamination. So, I came back to the engine and wanted to set the timing and be finished in the engine bay. However, I just couldn’t get it to start! After much checking and re-checking and rotating the distributor more ways than I thought would be possible, I finally got it to bite. At TDC and on the compression stroke, the distributor is pointing at No 1 cylinder, so with a little movement I can initially have the engine running and then it dies. Holding down the throttle does not help, but if I keep revving the throttle I can keep the engine running for maybe 20-30 seconds, then I hear misfires and it dies. Cables, plugs etc. are all new and in expected condition. There is no blockage in the air/filter and although fuel seems good, it primes and there is fuel at the rail, but is it good? Should I just throw money at a new pump and assembly unit and hope for the best?
Any advice would be most appreciated. Thanks.
|
|
|
Patrick
|
JUN 22, 12:51 PM
|
|
| quote | Originally posted by Darthscooby1001:
Should I just throw money at a new pump and assembly unit and hope for the best?
|
|
No... check the actual fuel pressure! It's so simple to do on the 2.8 V6.
| quote | Originally posted by Darthscooby1001:
At TDC and on the compression stroke, the distributor is pointing at No 1 cylinder, so with a little movement I can initially have the engine running and then it dies.
|
|
Make sure the outer ring of the harmonic balancer hasn't begun to spin on the hub. If it has, then the ignition timing marks will be useless.[This message has been edited by Patrick (edited 06-22-2026).]
|
|
|
Dennis LaGrua
|
JUN 22, 05:17 PM
|
|
This problem could be the result of many faults. Its usually spark or fuel. I would first measure the fuel pressure as Patrick has suggested at the Schrader valve connection on the fuel rail. You could buy an inexpensive pressure gauge to measure it. It might be a good idea to check if the harmonic balancer timing marks are correct. You will need to remove the no 1 spark plug and use a dial indicator to see if the piston is at top dead center. Piston all the way up will be TDC or 180* out but only one will be TDC. If that is incorrect then replace the balancer.------------------ " THE BLACK PARALYZER" -87GT 3800SC Series III engine, custom ZZP /Frozen Boost Intercooler setup, 3.4" Pulley, Northstar TB, LS1 MAF, 3" Spintech/Hedman Exhaust, P-log Manifold, Autolite 104's, MSD wires, Custom CAI, 4T65eHD w. custom axles, Champion Radiator, S10 Brake Booster, HP Tuners VCM Suite. "THE COLUSSUS" 87GT - ALL OUT 3.4L Turbocharged engine, Garrett Hybrid Turbo, MSD ign., modified TH125H " ON THE LOOSE WITHOUT THE JUICE "
|
|
|
Darthscooby1001
|
JUN 23, 10:06 AM
|
|
My fuel pressure gauge doesn't have any attachments or adapters, so I have just order another (Prime Day ). Of course when I first prime the FP there is definitely pressure as pressing the shrader valve producing a small fountain of fuel! Firebirds are approx 42 psi, what would a V6 be, similar and is that consistent?
The Harmonic Balancer is new and is the type without a timing mark. I therefore marked it whilst building the engine and since verified it again that it is TDC through the spark plug.
Thanks[This message has been edited by Darthscooby1001 (edited 06-23-2026).]
|
|
|
cartercarbaficionado
|
JUN 23, 11:59 AM
|
|
| quote | Originally posted by Darthscooby1001:
My fuel pressure gauge doesn't have any attachments or adapters, so I have just order another (Prime Day ). Of course when I first prime the FP there is definitely pressure as pressing the shrader valve producing a small fountain of fuel! Firebirds are approx 42 psi, what would a V6 be, similar and is that consistent?
The Harmonic Balancer is new and is the type without a timing mark. I therefore marked it whilst building the engine and since verified it again that it is TDC through the spark plug.
Thanks
|
|
do me a favor and tell me what your oil pressure light or gauge does, and fieros are about the same as its 36-45, 43 being whats specified i also want you to use a spark tester on number 1 and record what happens when it stalls out. i have a feeling its either a shitty coil/icm(pickup can also do weird things) or its shutting the fuel pump off after the 5 second prime[This message has been edited by cartercarbaficionado (edited 06-23-2026).]
|
|
|
Darthscooby1001
|
JUN 25, 10:16 AM
|
|
Fuel pressure is...... non existent, or maybe a 1psi, maybe. To ensure the gauge was not at fault I tested my Firebird and it works just fine.
Oil pressure was reading low on the dash indicator, but I wanted to get the car running before exploring that problem. There is a new pump in there, a new oil pressure sender and I can also see that oil is up in the valves, albeit a little milky. At first I was assuming it was left over break-in oil/lube, but the dip stick is clean oil. Now I can't remember if I used sealant on the head threads? however, that is not the issue right now. Can I assume with next to no fuel pressure, the old pump and sender I found in a spare tank is dead?
Thank you.
|
|
|
olejoedad
|
JUN 25, 11:37 AM
|
|
| quote | Originally posted by Darthscooby1001:
Fuel pressure is...... non existent, or maybe a 1psi, maybe. To ensure the gauge was not at fault I tested my Firebird and it works just fine.
Oil pressure was reading low on the dash indicator, but I wanted to get the car running before exploring that problem. There is a new pump in there, a new oil pressure sender and I can also see that oil is up in the valves, albeit a little milky. At first I was assuming it was left over break-in oil/lube, but the dip stick is clean oil. Now I can't remember if I used sealant on the head threads? however, that is not the issue right now. Can I assume with next to no fuel pressure, the old pump and sender I found in a spare tank is dead?
Thank you. |
|
If you have no fuel pressure, the pump is bad. The sender function can be tested by moving the float and checking resistance (ohm) readings.
|
|
|
cvxjet
|
JUN 25, 02:05 PM
|
|
|
If you get good pressure when priming the pump, but then it drops to zero when trying to run, sounds like your pressure regulator is bad...
|
|
|
Patrick
|
JUN 25, 03:00 PM
|
|
| quote | Originally posted by Darthscooby1001:
Can I assume with next to no fuel pressure, the old pump and sender I found in a spare tank is dead?
|
|
It's probably a bad fuel pump, but...
There's a chance that the short length of hose inside the gas tank that the fuel pump connects to has failed/rotted. Either way, you need to drop the tank to investigate.
Or maybe you're very lucky and it's just that the fuel filter is plugged.
|
|
|
Darthscooby1001
|
JUN 26, 06:21 AM
|
|
Thanks for the advice (so far). I've ordered a new FP (Rock Auto) & Sender (Fiero Store), which unfortunately is out of stock, so I have to wait a bit longer.
I doubt the regulator is bad as it was one of the umpteen parts I replaced.
I didn't like using the old pump I had found, despite looking in okay condition, so happy to have ordered a new one. I'll be back with either an update or further problems. In the meantime I just need to take the valve covers off and add RTV to all of the head bolts. Yes I am going to reuse them as the car has not move since their install.
Thanks
|
|

 |
|