1988 MERA GT 2.8L overheating (Page 1/3)
jrr DEC 11, 04:51 PM



I have an original 1988 Mera. Stock 2.8L V6 Engine. Always ran great no issues. Recently I upgraded to a PISA Euro Dash with aftermarket gauges. I have near everything working with the exception of the temp gauge overheating.

If anyone has seen my posts I even changed the charging dash light to incandescent as suggested. I also have the original oil pressure gauge attached in the glove box and original sender being used until I can make a "T" for both the original and aftermarket sender to be used.

Here is what I have done thus far to address the overheating:
1. Opened all of the caps - fill, radiator, and overflow.
2. I removed the thermostat.
3. I pulled out all of the antifreeze with a shop vac. Then flushed it complete for a long time with water.
4. (Near impossible to get to the drain plug on a Mera due to the front valance)
5. From the fill tube, the water was easily and forcefully coming out of the radiator.
6. This car has about 60,000 miles and there was very little rust and or debris.
7. After the flush, with the vacuum pulling from the fill and all of the water removed, I had hard suction from the radiator.
8. This leads me to believe there are no clogs in the system.
9. With the car on a slope I refilled the overflow first to the proper level.
10. Then filled antifreeze from the fill tube until I saw antifreeze coming out of the top of the radiator.
11. Then topped off antifreeze at the fill tube and closed the cap.
12. Note: I see all of these videos to turn on the engine and look for bubbles.
13. When I turn on the engine I am getting antifreeze pouring out of the fill tube.
14. This leads me to believe the water pump is working well. Also when I squeeze the top hose I can feel fluid flowing.
15. I turned on the heat to allow for antifreeze to run through the core. Then let it cool and topped it off (maybe 1/4 cup).
16. Now I am letting it cool with the back jacked up high to see if this makes any difference. (BTW it did not)

If I drive it around the block without a thermostat it runs up t0 210 + on the gauge. This is another thing not making sense. With a laser thermal scanner the manifold is 140-150, the fill tube is 140, the valve cover is 140 or less. If I put the laser directly on the temperature sender I am getting 215-225 degrees.

Can anyone please explain this or what to do? The 2 wire aftermarket sender must be wired to the signal and another side to ground which does not make any sense since it is attached to the engine but this is what they told me from the manufacturer. I cannot use the old gauge as it is built into the old cluster.

My next step is to install another gauge which wires up normally with one wire to the signal and the sender itself if grounded to the block. Any suggestions are greatly appreciated!

[This message has been edited by jrr (edited 12-11-2025).]

Patrick DEC 11, 07:05 PM

quote
Originally posted by jrr:

Any suggestions are greatly appreciated!



Paragraphs, my man... learn to use paragraphs.

[EDIT] Much better!


quote
Originally posted by jrr:

I turned on the heat to allow for antifreeze to run through the core.



Coolant is continually running through a Fiero's heater core.

[This message has been edited by Patrick (edited 12-12-2025).]

olejoedad DEC 12, 09:01 AM
To me it sounds like the sending unit and the aftermarket gage are not compatible.

Gages and sending units communicate via resistance values, the two units must have compatible scaling.

What brand of aftermarket gage are you using?
Patrick DEC 12, 05:01 PM

quote
Originally posted by jrr:

I have an original 1988 Mera. Stock 2.8L V6 Engine. Always ran great no issues. Recently I upgraded to a PISA Euro Dash with aftermarket gauges. I have near everything working with the exception of the temp gauge overheating.

Here is what I have done thus far to address the overheating...




What evidence is there of "overheating"? Is coolant puking out of the reservoir?

As posted above, it sounds more like an issue with the sender and/or gauge not working properly together.

You've been jumping through hoops to double-check your cooling system, yet a quick scan would've told you what the actual coolant temperature is as reported to the ECU by the CTS (Coolant Temperature Sensor).

If by some chance there is a problem with your cooling system, These are the steps I take when servicing mine.

[This message has been edited by Patrick (edited 12-12-2025).]

82-T/A [At Work] DEC 13, 09:18 AM

quote
Originally posted by Patrick:
What evidence is there of "overheating"? Is coolant puking out of the reservoir?

As posted above, it sounds more like an issue with the sender and/or gauge not working properly together.

You've been jumping through hoops to double-check your cooling system, yet a quick scan would've told you what the actual coolant temperature is as reported to the ECU by the CTS (Coolant Temperature Sensor).

If by some chance there is a problem with your cooling system, These are the steps I take when servicing mine.




Yeah... I kind of want to piggy back on this. I went through a ton of hoops to solve a cooling issue. I did end up having a cracked cyl head, which I eventually replaced... but a lot of my problems turned out to be a string of bad coolant sensors... which even includes the CTS. I've got the opposite problem where it shows my car never gets above 100 degrees, when clearly it is.

But yeah, if you have a way to read the ALDL feed and get informationo from the CTS... it'll tell you what the actual temperature is (unless that sensor is bad too, such as in my case, haha).
jrr DEC 18, 12:17 PM
Updates:
1. Removed the old antifreeze + thermostat and did a complete chemical and water flush.
2. Removed the radiator and cleaned + straightened the very few bent fins. (Very dirty and clogged on the bottom after 35+ years)
3. BTW - no need to remove the hood. Fan 2 bolts, shroud 4 bolts, popped the plastic pins, removed the hoses and it came out easily.
4. Reinstalled with new 50/50 Antifreeze mix with the rear raised significantly, burped several times. No air pockets, + without Thermostat.
4. Ran at idle and then drove it for 4-5 miles on a 65 degree cool day.
5. Without the thermostat it is running between 175-185 but not where it was before at 210 degrees.
6. Shouldn't the temp be 140-150 degrees on a cool day without a thermostat?
7. Next step will be to test on a hot day. If it runs past 210, I am going to replace the radiator and add a high CFM fan.
Thoughts? Thank you! JRR
82-T/A [At Work] DEC 18, 12:25 PM

quote
Originally posted by jrr:

6. Shouldn't the temp be 140-150 degrees on a cool day without a thermostat?




Not always. Sometimes, without a thermostat, the coolant can go through the radiator and cooling passages so quickly that it doesn't actually have time to cool off like it should. Not totally uncommon, but improved airflow, etc... can help with that.


You know... double check something for me. Make sure that the fan is running in the correct direction and sucking air through the radiator and back out...

jrr DEC 19, 03:42 PM
Thank you! Yes fan is definitely pulling is into the engine compartment.
infinitewill DEC 19, 04:45 PM

quote
Originally posted by jrr:

Thank you! Yes fan is definitely pulling is into the engine compartment.



Huh? The engine compartment is in the rear and there is no fan there.
jrr JAN 13, 07:43 PM
Sorry I meant to say the fan is pulling air through the radiator as designed.
Update:
1. Flushed the entire cooling system
2. Removed the radiator completely. (On a Mera you do not need to remove the hood) Actually fairly easy.
3. After 37 years the entire bottom of the radiator fins were clogged with dirt & debris. - Cleaned and straightened all the fins.
3. Replaced thermostat with a 160 degree. (Yes 160!). Replaced with new Antifreeze 50/50.
4. Went on a 60 mile stop and go + traffic trip. - Car ran mostly in the 180-190 range.
5. Turning on the AC brought it back to 180 when it hit 190+ - It never got anywhere near the 210+ degrees it was getting to before.
6. Weather here was in the 70's. I will have to test closer to the summer when it gets into the 90's.
7. If it runs too hot during the summer, ill spring for a new high speed fan and rad kit.
8. I know these are supposed to run at 195 to 200 but I do not like when it starts hitting 210+ with an original 37 year old engine
Will see what happens in a few months. Thanks for all of the feedback