 
     |
| STORAGE BIN DOOR (Page 1/2) |
|
RPYRAZOO
|
APR 25, 01:00 PM
|
|
Is it possible to remove the entire console assembly without removing the seats? My storage door under the rear window came off due to the nuts falling off and I figure the only way to reassemble it is to take the console out and reattach the nuts. I'd rather not have to take the seats out.
Thanks, R
|
|
|
|
JMTUT
|
APR 25, 01:22 PM
|
|
|
The entire rear center console will come out without removing seats. 6 screws in the console. 2 behind the door 2 in front. 2 holding the lighter/aldl cover on. You have to remove the center cap over the gear shift 1st. 2 screws under each ashtray. You also need to disconnect the wires on the lighter or remove the 2 screws holding it on. [This message has been edited by JMTUT (edited 04-25-2019).]
|
|
|
Patrick
|
APR 25, 06:07 PM
|
|
| quote | Originally posted by RPYRAZOO:
I'd rather not have to take the seats out.
|
|
Why not? Think of all the money you'll find! 
|
|
|
|
theogre
|
APR 26, 12:24 AM
|
|
While out, See my Cave, ECM Heat
------------------
Dr. Ian Malcolm: Yeah, but your scientists were so preoccupied with whether or not they could, they didn't stop to think if they should.
(Jurassic Park)
The Ogre's Fiero Cave
|
|
|
RPYRAZOO
|
APR 27, 02:28 PM
|
|
JMTUT: Thanks, just what I needed to know.
Patrick: No $ left, got it all ( $1.25 ) when I replaced the carpet. Removing the seats was the most PITA part of the process, that's why I don't want to have to do it again.
Ogre: Great idea, I'll do what you recommend when I get it all apart.
Thanks guys........again,
Rich
|
|
|
|
Dennis LaGrua
|
MAY 01, 03:09 PM
|
|
|
Normal commercial temp range for integrated circuits is 0-70*C . That's a standard 158* F but in most cases automotive parts use an industrial rated part that is good from -40* to 125*C. I would not be too concerned about the ECM / PCM overheating.. ------------------
" THE BLACK PARALYZER" -87GT 3800SC Series III engine, custom ZZP /Frozen Boost Intercooler setup, 3.4" Pulley, Northstar TB, LS1 MAF, 3" Spintech/Hedman Exhaust, P-log Manifold, Autolite 104's, MSD wires, Custom CAI, 4T65eHD w. custom axles, Champion Radiator, S10 Brake Booster, HP Tuners VCM Suite.
"THE COLUSSUS"
87GT - ALL OUT 3.4L Turbocharged engine, Garrett Hybrid Turbo, MSD ign., modified TH125H
" ON THE LOOSE WITHOUT THE JUICE "
|
|
|
Patrick
|
MAY 01, 03:19 PM
|
|
| quote | Originally posted by RPYRAZOO:
No $ left, got it all ( $1.25 ) when I replaced the carpet.
|
|
Only $1.25?  That's surprising!
| quote | Originally posted by RPYRAZOO:
Removing the seats was the most PITA part of the process, that's why I don't want to have to do it again.
|
|
Four nuts to remove for each seat... that was a PITA?  It's like a five minute job, tops. Were they badly corroded or what?
|
|
|
cliffw
|
MAY 01, 08:00 PM
|
|
|
|
|
olejoedad
|
MAY 02, 08:21 AM
|
|
|
A 13mm ratcheting wrench make seat removal a breeze.
|
|
|
|
RPYRAZOO
|
MAY 05, 01:16 PM
|
|
Patrick, those 4 little nuts were almost the cause of my calling a mental health pro. They were rusted beyond repair and had to access them from underneath and from above.
R
|
|
|
|