2.0L LTG Engine Swap? (Page 1/3)
gln103 OCT 26, 03:50 PM
I've looked unsuccessfully for a 2.0L GM LTG engine (http://www.chevrolet.com/pe...g-four-cylinder.html) build thread. A PFF search only finds "LTG" in 9 threads, and none are close to discussing build details. With these engines being used in the Buick Regal, Malibu, Cadillac ATS, Cadillac CTS, Cadillac CT6, and Camaro, used engines are starting to pop up for ~$2,000.

I'm looking for a swap to my 1987 2.8L, 5-speed manual GT that will give something in the 250-300 hp range, keep the car light, and also gets decent fuel economy. The LTG engine seems to fit the bill, so it's interesting no one has done this swap yet. Maybe I'm missing something?

What are thoughts on the feasibility of this swap (2.8L, 5 speed manual to a 2.0L LTG keeping the 5 speed manual)? Have any of the performance shops created a kit yet? What are the biggest hurdles?

Thanks,
Gary
dobey OCT 26, 04:11 PM
No, there is no kit to swap one into a Fiero.

Not sure what 5 speed manual you're referring to that would come with the LTG though. The manual transmission which comes in the FWD cars equipped as such, should be an F40 six speed.

You'll likely need to also convert the wheel hubs to something capable of having ABS sensors as well, as the Ecotec F40 trans does not have a VSS and the computer gets this from the wheel speed sensors instead.
gln103 OCT 26, 04:31 PM
Sorry, maybe my post wasn't clear. I'm proposing swapping in the LTG and keeping the stock Fiero 5 speed manual transmission.
dobey OCT 26, 04:40 PM

quote
Originally posted by gln103:

Sorry, maybe my post wasn't clear. I'm proposing swapping in the LTG and keeping the stock Fiero 5 speed manual transmission.



I wouldn't do that. They aren't the same bell housing, so you'd need an adapter plate. The gearing in the F40 is also better suited to the smaller 4 cylinder, and you'll want the 6th gear for highway cruising.

If you want to stay with a 5 speed, swapping in an F35 from one of the turbo Cobalt SS cars would probably be a better option than the stock Fiero trans.
mender OCT 27, 01:15 AM
Or an ecotec F23 with a Dakota Digital SGI-5 to convert the VSS signal.

[This message has been edited by mender (edited 10-27-2016).]

gln103 OCT 27, 07:56 AM
Good transmission comments. If we use an F35 or F40, I assume we would need new halfshafts, clutch interface, and shift mechanism? If so, then we have to pick our poison (bellhousing and flywheel adapters vs. custom halfshafts, shift mechanism, and clutch interface).

Thanks,
Gary
dobey OCT 27, 08:10 AM
Well, not just that. The depth for the bell housing is not the same across all the transmissions. You won't need a "flywheel adapter" to use the Fiero 282, but you'll need an entirely custom flywheel. The Fiero 282 is also not rated or built to handle the same amount of power that the F35 or F40 are. Depending on how you are going to drive the car, you might find yourself needing to replace the trans soon enough if you stick with the 282 anyway.

I think ZZP has a half-shaft and bracket available with the ring for a VSS. Other than that, the half shaft can be the stock one from Cobalt/Regal/etc… and you will need mounts and maybe custom axles.

All of these are part of the reason the LNF/LTG swaps haven't been done yet, and why there aren't many other Ecotec swaps either. The 3800 is a cheaper and easier swap, so it's what most everyone does. If you want cheap, easy, reliable, and good MPG, the Series III 3800 N/A is 240+ HP stock, bolts right up to the Fiero 282 trans, uses a turned down Camaro 3800 flywheel, and can get you ~38 MPG on the highway.
mender OCT 27, 11:39 AM
I think the F23 is going to become the universal Fiero swap transaxle in the very near future, uses stock axles, has VSS signal, 60 degree, Quad4 and Ecotec bellhousings, cheap and strong, the details are already sorted out.

I have all four of the transaxles in question (282, F23, F35 and F40) and in most of the varieties available; no HF F40 though.

[This message has been edited by mender (edited 10-27-2016).]

dobey OCT 27, 01:29 PM

quote
Originally posted by mender:

I think the F23 is going to become the universal Fiero swap transaxle in the very near future, uses stock axles, has VSS signal, 60 degree, Quad4 and Ecotec bellhousings, cheap and strong, the details are already sorted out.

I have all four of the transaxles in question (282, F23, F35 and F40) and in most of the varieties available; no HF F40 though.




I'd rather use the half-shaft than stock axles though, and the F23 still isn't a straight bolt-in option. It's a decent option for a manual 3800 or a Quad4 swap, but for any FWD engine from the last ~10 years or so or newer, grabbing at least a whole cradle drop out, if not the entire car, will make a swap much easier.
wftb OCT 27, 02:35 PM
The f35 from the cobalt SS supercharged will bolt up to all 2.2 , 2.4 ,2.0 ecotecs .These axles fit Fiero hubs too .Engines that came out of automatic cars will need some swapping out of thermostat housings because of interference issues .Axles from this tranny can be used in f40 's .
f35 from the turbo cobalt ss uses a larger diameter spline going to the hub so it cant be adapted to a fiero hub .The wheel bolt pattern is also larger than the 5 x 100 of the fiero .
If you are doing an ecotec swap , the f23 from a 2.2 ecotec equipped cavalier /cobalt is the easiest because you can use the fiero axles .