 
     |
| Project 3400 Roller Cam Block (Page 39/82) |
|
Will
|
MAY 05, 01:19 PM
|
|
That's a pretty good 4.9 dyno.
My stock Northstar beat that by 1 ftlb and 70 HP. 
|
|
|
|
lou_dias
|
MAY 05, 02:37 PM
|
|
| quote | Originally posted by Will:
That's a pretty good 4.9 dyno.
My stock Northstar beat that by 1 ftlb and 70 HP. |
|
Yeah, we both know it's crap (yet amazingly close to by 3.400 car). That was with a stickpony chip (which is just an ADS chip) ... I didn't get the 4.9 swap for horsepower. NJD85GT send me a much better tune and it runs a lot better now but now I get clutch slip at 4200+... Its just my daily driver now since my stock 88 Formula developed a crack in the cross-over.[This message has been edited by lou_dias (edited 05-05-2013).]
|
|
|
|
lou_dias
|
MAY 07, 12:25 PM
|
|
|
New spindle showed up yesterday. Supposedly to be installed today. I hope this one is correct.
|
|
|
|
ericjon262
|
MAY 07, 07:57 PM
|
|
| quote | Originally posted by lou_dias:
Yeah, we both know it's crap (yet amazingly close to by 3.400 car). That was with a stickpony chip (which is just an ADS chip) ... I didn't get the 4.9 swap for horsepower. NJD85GT send me a much better tune and it runs a lot better now but now I get clutch slip at 4200+... Its just my daily driver now since my stock 88 Formula developed a crack in the cross-over.
|
|
if your "3400 car" is the car this thread is about, it's not a 3400 anymore, merely a roller cam 3.4.
|
|
|
|
lou_dias
|
MAY 08, 12:45 PM
|
|
| quote | Originally posted by ericjon262:
if your "3400 car" is the car this thread is about, it's not a 3400 anymore, merely a roller cam 3.4. |
|
Put on your glasses. I said 3 POINT 400.
|
|
|
|
sleevePAPA
|
MAY 08, 01:12 PM
|
|
| quote | Originally posted by lou_dias:
Put on your glasses. I said 3 POINT 400. |
|
a reverse hybrid LOL
|
|
|
|
carbon
|
MAY 08, 11:10 PM
|
|
Technically its a 3350 stock... 
|
|
|
|
lou_dias
|
MAY 09, 07:48 AM
|
|
| quote | Originally posted by carbon:
Technically its a 3350 stock... |
|
Yes but mine is bored .020" over so it is a true 3.40000000000 ;-)
A stock 3.4/3400 uses a 3.62" bore. I'm at 3.64" and a 3500 LX9 uses a 3.7" bore. If I ever rebuild this block (again) maybe I'll just have it bored to that. They had the car running yesterday and were preparing the bill. Not looking forward to the bill but at least I'll have the car tonight - FINALLY![This message has been edited by lou_dias (edited 05-09-2013).]
|
|
|
|
RacerX11
|
MAY 09, 05:13 PM
|
|
| quote | Originally posted by lou_dias:
Yes but mine is bored .020" over so it is a true 3.40000000000 ;-)
|
|
More like 3.387 if you want to be exact.
|
|
|
|
lou_dias
|
MAY 10, 09:03 AM
|
|
|
Alignment is way off. Coolant is low and it needs an inspection sticker so I dropped the car off this morning at a local shop.
|
|
|
