 
     |
| The Turbo 3500 F23 swap (Page 36/80) |
|
ericjon262
|
JUL 13, 10:18 AM
|
|
|
. [This message has been edited by ericjon262 (edited 09-11-2022).]
|
|
|
|
engine man
|
JUL 13, 11:31 AM
|
|
|
you are trying to guide the push rods right so the rockers wont turn ? if that is what you are looking to do why not get BBC guide plates and cut them in the middle if needed and make them the width you need bolt them to a bare spare head and weld back together it is just a thought and by the way you are doing a great job would love to see this car some day [This message has been edited by engine man (edited 07-13-2016).]
|
|
|
|
ericjon262
|
JUL 13, 01:50 PM
|
|
|
. [This message has been edited by ericjon262 (edited 09-11-2022).]
|
|
|
|
ericjon262
|
JUL 15, 05:37 PM
|
|
|
good news, alternator bracket works, no odd noises or anything, belt wasn't destroyed in seconds, nothing exciting happened, it just worked! the car didn't overheat for the short time I ran it in the driveway, which is another plus!
|
|
|
|
ericjon262
|
JUL 16, 07:47 PM
|
|
|
|
|
ericjon262
|
JUL 25, 06:52 PM
|
|
|
. [This message has been edited by ericjon262 (edited 09-11-2022).]
|
|
|
|
ericjon262
|
AUG 04, 04:04 AM
|
|
|
. [This message has been edited by ericjon262 (edited 09-11-2022).]
|
|
|
|
KaijuSenso
|
AUG 04, 05:38 PM
|
|
| quote | Originally posted by ericjon262:
so, the oil line to the turbo blew the hose end off, not 100% sure if it was an install error, material failure, or a combination of the two. either way, the turbo is trashed, new ebay turbo on the way to replace it for the time being |
|
Awe man seriously!? Was there something building pressure in the line like a plug in the turbo or something?
|
|
|
|
ericjon262
|
AUG 05, 01:42 AM
|
|
|
. [This message has been edited by ericjon262 (edited 09-11-2022).]
|
|
|
|
Dennis LaGrua
|
AUG 05, 06:45 AM
|
|
| quote | Originally posted by ericjon262:
to my knowledge, no, it is possible, but I have no evidence to suggest what exactly caused it.
|
|
If you are running oil to a turbo a standard rubber oil line held on a hose nipple by clamps will not hold. Either use a steel line, double flared with brass fittings (preferred) at the ends or AR fittings and stainless steel braided lines. ------------------
" THE BLACK PARALYZER" -87GT 3800SC Series III engine, custom ZZP /Frozen Boost Intercooler setup, 3.4" Pulley, Northstar TB, LS1 MAF, 3" Spintech/Hedman Exhaust, Autolite 104's, MSD wires, Custom CAI, 4T65eHD w. custom axles, HP Tuners VCM Suite.
"THE COLUSSUS"
87GT - ALL OUT 3.4L Turbocharged engine, Garrett Hybrid Turbo, MSD ign., modified TH125H
" ON THE LOOSE WITHOUT THE JUICE "
|
|
|
|