2.0L LTG Engine Swap? (Page 3/3)
dobey OCT 30, 09:23 PM

quote
Originally posted by gln103:

With a turbocharged engine swap, how have people dealt with the intercooler? I'm guessing routing air to a front-of-the-car mounted intercooler is out of the question, but there's basically no room or air flow in the engine bay area to mount an intercooler, right?



Air/water system, or go with meth injection without an IC, or just no IC, depending on how much boost is going to be run.
wftb OCT 30, 10:53 PM
I have air to water IC as well as water /meth . I have run an air to air where the cat used to be , but intake temps were about 15* F higher than air to water .
BillS OCT 31, 04:56 PM
At the pressures those engines use an IC is mandatory. Locating one in a Fiero so that the flow is adequate is a bit problematic.

I wonder if one could be mounted in modified rear wing, and if flow would then be enough to keep it cool.

I run my LNF to 26-26 psi. You can't run more than 10-12 psi without an IC - it becomes diminishing returns as every psi of added pressure adds heat which offsets the power you were hoping to gain from the increased pressure.
dobey OCT 31, 08:47 PM

quote
Originally posted by BillS:

At the pressures those engines use an IC is mandatory. Locating one in a Fiero so that the flow is adequate is a bit problematic.

I wonder if one could be mounted in modified rear wing, and if flow would then be enough to keep it cool.

I run my LNF to 26-26 psi. You can't run more than 10-12 psi without an IC - it becomes diminishing returns as every psi of added pressure adds heat which offsets the power you were hoping to gain from the increased pressure.



No. Knock reduction measures are necessary. An air-to-air inteercooler is only one method, and is not an efficient or effective application in a Fiero. An air/water intercooler, and/or meth injection are going to be more effective in a Fiero. i would say it's more like 7-8 PSI max with no knock reduction methods at all in a Fiero. But air/water intercooler, meth injection, and/or E85 as only fuel, are all decent methods. There's also a lot that can be done with the LTG in terms of electronic boost control and timing, to prevent knock. It won't make as much power if you pull boost pressure or timing out, but it will save the engine.Combined with good knock prevention methods, such as methanol injection, and running E85, though, the boost and timing can be maintained to make maximum power (which you won't used on the street anyway).
wftb OCT 31, 09:57 PM
You are forgetting that all new turbo ecotec motors are direct injected .They run usually in the 18 psi range and they already have air to water intercoolers built in .I do not know wether they are setup as flex fuel engines but seeing as most newer cars are that would probably be the case .Direct injection cools the pistons and allows higher compression and higher boost pressures .
dobey NOV 01, 08:39 AM

quote
Originally posted by wftb:

You are forgetting that all new turbo ecotec motors are direct injected .They run usually in the 18 psi range and they already have air to water intercoolers built in .I do not know wether they are setup as flex fuel engines but seeing as most newer cars are that would probably be the case .Direct injection cools the pistons and allows higher compression and higher boost pressures .



The intercooler is not "built in" to the engine. And I'm pretty sure they use air-air intercoolers mounted in front of the radiator. The intake piping definitely runs to/from the bottom front of the car. There's no air/water interchange box anywhere near the engine itself.

DI doesn't really "cool the pistons." However, the new engines do have oil jets which spray the bottom of the pistons to help cool them. What DI does is keep the fuel out of the chamber until nearly the end of the compression cycle, which greatly reduces the chance of detonation. That's what allows the higher CR and boost levels.
wftb NOV 01, 12:17 PM
DI definitely cools the pistons .The shot of cool gasoline hitting the centre of the piston before the flame starts has a big cooling effect on it .The oil squirters have an affect too but no where near as much because of the high temperature of the oil .Better than nothing but not even close to DI .The gasoline charge coming in to an NA engines has a cooling effect as well .Engines that have gas starved conditions develop at high speeds on tracks like Daytona have had the tops of pistons melt .
wftb NOV 01, 01:04 PM
You can buy a brand new crate engine LTG from GM for only 9000.00 LOL .Optional stand alone wiring and ECM system that I did not see a price on . It does not have a built in intercooler that is correct .In the description it says that intercooling is mandatory and IAT should never be allowed to go above 140C .That seems really high , I would not dare to run my engine with intake temps above 60 C .The oiling system description makes no mention of piston squirters .I went to a GM description of the production motor and it said that they used piston skirt oilers .I also learned that the engine is entirely new design and has dimensions in common with previous turbo ecotecs but I got the impression that nothing is interchangeable with the old engines .

[This message has been edited by wftb (edited 11-01-2016).]

wftb NOV 01, 01:25 PM
All about the LTG . http://gmauthority.com/blog/gm/gm-engines/ltg/
a_monkie AUG 17, 12:00 PM
Just wanted to come in this decade-old thread to provide some clarification:

The third gen Ecotecs(LTG, LCV, LKW) have a different bellhousing than the second gen engines.

This means without an adapter the F23, F35, and most F40s are not compatible.

The only natively compatible manual transmissions are the F40(2014-2015 Buick Regal) for FF or MR applications. You should be able to swap the bellhousing half of the F40 housing, so you could theoretically use an older F40 with the Gen2 Ecotec pattern (not G6 pattern, different housing bolt pattern) with the newer gen 3 bellhousing. If you happen to stuble into a cheap broken Gen3 F40 to take the bellhousing from.

For FR applications you can use the Tremec TR-3160 (2016-2023 Camaro, 2014-2018 Cadillac ATS) or the Eaton N8D (2015-2019 Chevrolet Colorado/GMC Canyon)

The TR-3160 and N8D are pretty chunky, which could make swaps difficult. Also take shifter position into account.