I have a 88 base model for parting out. Got it with a "knocking" motor... Have never head it run. Its has a isuzu 5 speed and a iron duke engine. I have already removed the full 5 speed components but may still sell the trans. 140k on the car
List of things gone: sail windows fuel lines tail lights deck lid lock center console skeleton shifter surround (not the trip plate) full front suspension full rear suspension/cradle etc. Iron duke head/intake and ignition brick all the coolant hoses radiator fan steering column side scoop lower front air dam headlight harness (and motors)
[This message has been edited by JHarvey (edited 04-24-2013).]
I need the rad support that bolts from frame rail to fram rail. and both reflectors from the rear bumper. Getting the horn buttons would be nice too. .... highsugarcount@hotmail.com ...... the best way to reach me. bamman
I need the rad support that bolts from frame rail to fram rail. and both reflectors from the rear bumper. Getting the horn buttons would be nice too. .... highsugarcount@hotmail.com ...... the best way to reach me. bamman
I'm not sure what you mean by the rad support that bolts from frame rail to frame rail. I have the reflectors and as for the horn buttons, would you be interested in the whole wheel?
IP: Logged
12:23 AM
mptighe Member
Posts: 3321 From: Houston, TX Registered: Aug 2009
I'm still looking for one 88 heater hose so I can get going on all the rubber hoses for the 88's:
heater hose return that goes from the passenger coolant tube to the heater tube running up front.
I need an OEM GM original factory hose. Can be junky etc but needs to be complete and not altered.
------------------ Rodney Dickman
Fiero Parts And Acc's Web Page: All new web page!:www.rodneydickman.com Rodney Dickman's Fiero accessories 7604 Treeview Drive Caledonia, WI 53108 Phone/Fax (262) 835-9575
IP: Logged
10:20 AM
solotwo Member
Posts: 5374 From: Grand Rapids, MI. USA Registered: Jun 2002
I need a passengers side window, the marker light on the drivers side front and passengers side rear. The back hood lock too. It has the round molding. Thanks.
IP: Logged
01:20 PM
coady Member
Posts: 934 From: Ontario, Canada Registered: Aug 2012
I need a passengers side window, the marker light on the drivers side front and passengers side rear. The back hood lock too. It has the round molding. Thanks.
I kept the doors off of this car complete because my car has the typical scratched windows. Sorry
quote
Originally posted by DLCLK87GT:
i'm looking for an unmolested tail light harness with good sockets. PM me cost including shipping to 08055, thanks.
Replied
quote
Originally posted by Boostdreamer:
I'm interested in both front fenders and the front fascia, eggcrate, and related supporting hardware.
Where in Tennessee are you located? I'm in the northeast corner.
Jonathan
The front fenders are ripped along the bottom where they mount to the body. Sadly I have the front bumper though without chin spoiler.
IP: Logged
11:11 AM
UK86GT4.9 Member
Posts: 160 From: FT. KNOX, KY Registered: May 2012
Looking for the dot matrix radio and shifter surrounds (already have the gauge cluster).
I'll be using the shifter surround for the 5 speed swap. But I have the dot matrix radio trim but to be honest the top right corner was cracked where the screw goes in. Its been glued back together with gorilla glue and is almost not even noticeable. PM me if interested.
Bump: Still have some good parts left! 4cyl cluster 4 cyl manual computer 88 tank (with sending unit) Misc trip pieces 88 shell with clean title. (no panels, no suspension, no cradle, no interior/column etc. SHELL, thats it. List goes on
Still have some good parts left! 4cyl cluster 4 cyl manual computer 88 tank (with sending unit) Misc trip pieces 88 shell with clean title. (no panels, no suspension, no cradle, no interior/column etc. SHELL, thats it. List goes on
