Pennock's Fiero Forum
  General Fiero Chat - Archive
  Who can install a 3800 in a fiero (indiana)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Email This Page to Someone! | Printable Version


Who can install a 3800 in a fiero (indiana) by ANTEC900
Started on: 02-07-2011 05:22 PM
Replies: 15
Last post by: fieroguy123 on 02-08-2011 11:59 AM
ANTEC900
Member
Posts: 155
From: Mooresville IN
Registered: Oct 2010


Feedback score: N/A
Leave feedback

Rate this member

Report this Post02-07-2011 05:22 PM Click Here to See the Profile for ANTEC900Send a Private Message to ANTEC900Direct Link to This Post
Okay I am thinking of buying this 87GT 5 speed
And want someone to install a 3800 or 3800 sc in it
But I am not sure where to get it done
If you can do it please pm me a price range it will cost me and where you are located in indiana
IP: Logged
PFF
System Bot
L67
Member
Posts: 1792
From: Winston Salem, NC
Registered: Jun 2010


Feedback score:    (15)
Leave feedback





Total ratings: 219
User Banned

Report this Post02-07-2011 06:22 PM Click Here to See the Profile for L67Send a Private Message to L67Direct Link to This Post
Some of the best work you can buy is in your area.

http://gmtuners.com/
IP: Logged
fieroguy123
Member
Posts: 1523
From: Indianapolis
Registered: Sep 2009


Feedback score: (2)
Leave feedback





Total ratings: 62
Rate this member

Report this Post02-07-2011 06:35 PM Click Here to See the Profile for fieroguy123Send a Private Message to fieroguy123Direct Link to This Post
Good luck with that. He's backed up for like a year and a half.

------------------
May the Lord guide me where I must go. May the Fiero get me there in style

IP: Logged
RickN
Member
Posts: 2891
From: INDY, USA
Registered: Feb 2004


Feedback score: (2)
Leave feedback





Total ratings: 72
Rate this member

Report this Post02-07-2011 06:58 PM Click Here to See the Profile for RickNSend a Private Message to RickNDirect Link to This Post
 
quote
Originally posted by fieroguy123:

Good luck with that. He's backed up for like a year and a half.



That may be true but he occasionally has cancellations. I was the beneficiary of a cancellation and the bad economy last Dec '09.
His work is first class.

My '85GT...


------------------
RickN
White 88GT 5spd (<10K miles)
White 85GT (SC3800 Series II w/ AOD)
White 99 F250SD 7.3PSD 6spd
1956 Ford 860 Tractor w/ Freeman Loader
20Ft H&H Tilt Bed Trailer (Remember - Gravity is not a tie-down)

[This message has been edited by RickN (edited 02-07-2011).]

IP: Logged
weaselbeak
Member
Posts: 2604
From: se iowa
Registered: Jun 2008


Feedback score: (5)
Leave feedback





Total ratings: 76
Rate this member

Report this Post02-07-2011 07:55 PM Click Here to See the Profile for weaselbeakSend a Private Message to weaselbeakDirect Link to This Post
I sneaked mine in when he had a holdup on a transmission job. Ryan is 1st class.
IP: Logged
fieroguy123
Member
Posts: 1523
From: Indianapolis
Registered: Sep 2009


Feedback score: (2)
Leave feedback





Total ratings: 62
Rate this member

Report this Post02-07-2011 11:08 PM Click Here to See the Profile for fieroguy123Send a Private Message to fieroguy123Direct Link to This Post
That's exactly why he's always so backed up, his work is top notch 100% of the time.

------------------
May the Lord guide me where I must go. May the Fiero get me there in style

IP: Logged
RACE
Member
Posts: 4845
From: Des Moines IA
Registered: Dec 2002


Feedback score:    (45)
Leave feedback





Total ratings: 157
Rate this member

Report this Post02-08-2011 01:11 AM Click Here to See the Profile for RACEClick Here to visit RACE's HomePageSend a Private Message to RACEDirect Link to This Post
I have seen his work in person. It is better than factory original. If I had the cash he or Guru would be my choice. Both do excellent work.
IP: Logged
ANTEC900
Member
Posts: 155
From: Mooresville IN
Registered: Oct 2010


Feedback score: N/A
Leave feedback

Rate this member

Report this Post02-08-2011 09:30 AM Click Here to See the Profile for ANTEC900Send a Private Message to ANTEC900Direct Link to This Post
How good are his prices?
IP: Logged
datacop
Member
Posts: 1426
From: Indianapolis, IN, USA
Registered: Jan 2004


Feedback score: (5)
Leave feedback





Total ratings: 52
Rate this member

Report this Post02-08-2011 09:36 AM Click Here to See the Profile for datacopClick Here to visit datacop's HomePageSend a Private Message to datacopDirect Link to This Post
If you have to ask, you can't afford it.

You do realize that you're looking at $4,000 to $5,000 just for the labor right?
IP: Logged
ANTEC900
Member
Posts: 155
From: Mooresville IN
Registered: Oct 2010


Feedback score: N/A
Leave feedback

Rate this member

Report this Post02-08-2011 10:04 AM Click Here to See the Profile for ANTEC900Send a Private Message to ANTEC900Direct Link to This Post
O.o did not think it would be that much
I guess I will have to start saveing lol
Thanks for the help everyone
IP: Logged
datacop
Member
Posts: 1426
From: Indianapolis, IN, USA
Registered: Jan 2004


Feedback score: (5)
Leave feedback





Total ratings: 52
Rate this member

Report this Post02-08-2011 10:13 AM Click Here to See the Profile for datacopClick Here to visit datacop's HomePageSend a Private Message to datacopDirect Link to This Post
Yea man.. you're looking at spending $750 to $1500 just for the engine / harness / tranny / pcm / axles..

figure another $200 to $400 for the mounts

Figure another $500 for misc parts / wires / bolts / etc, etc.

So you're sitting at $1450 to $2400 just for the hardware needed to perform the swap... it would be a STEAL if you could find someone to do a quality install for just $2,000 labor.. more than likely it'll be double that for labor..

So you're looking at $5450 to $6400 to pay someone to do the swap..

If you were thinking that you could get away with an L67 swap for $1000 or less.. I'm sorry.. not going to happen... not with you paying someone else for the swap.
IP: Logged
PFF
System Bot
fieroguy123
Member
Posts: 1523
From: Indianapolis
Registered: Sep 2009


Feedback score: (2)
Leave feedback





Total ratings: 62
Rate this member

Report this Post02-08-2011 10:16 AM Click Here to See the Profile for fieroguy123Send a Private Message to fieroguy123Direct Link to This Post
The numbers that Datacop gave you are pretty darn accurate. The swap can be done with half-a#$ quality for around $1500 if you can do all the work yourself.

------------------
May the Lord guide me where I must go. May the Fiero get me there in style

IP: Logged
ANTEC900
Member
Posts: 155
From: Mooresville IN
Registered: Oct 2010


Feedback score: N/A
Leave feedback

Rate this member

Report this Post02-08-2011 10:28 AM Click Here to See the Profile for ANTEC900Send a Private Message to ANTEC900Direct Link to This Post
 
quote
Originally posted by fieroguy123:

The numbers that Datacop gave you are pretty darn accurate. The swap can be done with half-a#$ quality for around $1500 if you can do all the work yourself.


I can probably do most of it my self but I would probably get stuck and not know who to go to for help
IP: Logged
fieroguy123
Member
Posts: 1523
From: Indianapolis
Registered: Sep 2009


Feedback score: (2)
Leave feedback





Total ratings: 62
Rate this member

Report this Post02-08-2011 10:58 AM Click Here to See the Profile for fieroguy123Send a Private Message to fieroguy123Direct Link to This Post
Props to you if you attempt it. Feel free to give me a call if you need some guidance. I've done several 3800 swaps and I don't live too far from you. Northside of indy.

------------------
May the Lord guide me where I must go. May the Fiero get me there in style

IP: Logged
ANTEC900
Member
Posts: 155
From: Mooresville IN
Registered: Oct 2010


Feedback score: N/A
Leave feedback

Rate this member

Report this Post02-08-2011 11:20 AM Click Here to See the Profile for ANTEC900Send a Private Message to ANTEC900Direct Link to This Post
 
quote
Originally posted by fieroguy123:

Props to you if you attempt it. Feel free to give me a call if you need some guidance. I've done several 3800 swaps and I don't live too far from you. Northside of indy.



Okay cool
And anyone have a link that will tell me what all I will need to get like parts I will need for a swap
IP: Logged
fieroguy123
Member
Posts: 1523
From: Indianapolis
Registered: Sep 2009


Feedback score: (2)
Leave feedback





Total ratings: 62
Rate this member

Report this Post02-08-2011 11:59 AM Click Here to See the Profile for fieroguy123Send a Private Message to fieroguy123Direct Link to This Post
Get your mounts from purple reign or fieroX.
Get in touch with fieroflyer about having a harness made.
I have an exhaust guy that can hook you up.
Sinister Performance can reprogram the ecm for like 80 bucks
And I think purple reign makes the low mount alternator bracket too

------------------
May the Lord guide me where I must go. May the Fiero get me there in style

IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery
Real-Time Chat | Fiero Related Auctions on eBay



Copyright (c) 1999, C. Pennock