Pennock's Fiero Forum
  Technical Discussion & Questions - Archive
  Rear Muncie Trans Mount Bracket Same as Getrag?

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Email This Page to Someone! | Printable Version


Rear Muncie Trans Mount Bracket Same as Getrag? by Erik
Started on: 04-02-2008 07:34 PM
Replies: 5
Last post by: Erik on 04-04-2008 04:53 PM
Erik
Member
Posts: 5616
From: Des Moines, Iowa
Registered: Jul 2002


Feedback score: (3)
Leave feedback





Total ratings: 169
Rate this member

Report this Post04-02-2008 07:34 PM Click Here to See the Profile for ErikClick Here to Email ErikSend a Private Message to ErikDirect Link to This Post
It looks like the Fiero Muncie 4 speed rear trans mount bracket will bolt up to the FWD v6 getrag. Is the Fiero Muncie 4 speed rear trans bracket the same bracket as the Fiero v6 getrag rear bracket? ?
Also, will the quad 4 getrag trans have the same holes for mounting a Fiero V6 getrag trans brackets front and back as the v6 Fiero getrag does? I am going to use the FWD getrag v6 bellhousing and swap it onto the quad 4 trans so I am just trying to figure out what is needed for the mount bracket part of the swap

[This message has been edited by Erik (edited 04-03-2008).]

IP: Logged
PFF
System Bot
Erik
Member
Posts: 5616
From: Des Moines, Iowa
Registered: Jul 2002


Feedback score: (3)
Leave feedback





Total ratings: 169
Rate this member

Report this Post04-03-2008 01:31 PM Click Here to See the Profile for ErikClick Here to Email ErikSend a Private Message to ErikDirect Link to This Post
bump
IP: Logged
Erik
Member
Posts: 5616
From: Des Moines, Iowa
Registered: Jul 2002


Feedback score: (3)
Leave feedback





Total ratings: 169
Rate this member

Report this Post04-04-2008 02:18 PM Click Here to See the Profile for ErikClick Here to Email ErikSend a Private Message to ErikDirect Link to This Post
???
IP: Logged
Synthesis
Member
Posts: 12102
From: Jordan, MN
Registered: Feb 2002


Feedback score:    (19)
Leave feedback





Total ratings: 288
Rate this member

Report this Post04-04-2008 04:29 PM Click Here to See the Profile for SynthesisSend a Private Message to SynthesisDirect Link to This Post
I believe the rear one is the same between the Getrag and Muncie. The front mount OTOH is different.
IP: Logged
Rodney
Member
Posts: 4713
From: Caledonia, WI USA
Registered: Feb 2000


Feedback score: (4)
Leave feedback





Total ratings: 268
Rate this member

Report this Post04-04-2008 04:46 PM Click Here to See the Profile for RodneyClick Here to visit Rodney's HomePageClick Here to Email RodneySend a Private Message to RodneyDirect Link to This Post
The Getrag, Isuzu and Muncie rear brackets all look the same but do not interchange.

------------------
Rodney Dickman

Fiero Parts And Acc's Web Page:
www.rodneydickman.com
Rodney Dickman's Fiero accessories
7604 Treeview Drive
Caledonia, WI 53108
Phone/Fax (262) 835-9575

IP: Logged
Erik
Member
Posts: 5616
From: Des Moines, Iowa
Registered: Jul 2002


Feedback score: (3)
Leave feedback





Total ratings: 169
Rate this member

Report this Post04-04-2008 04:53 PM Click Here to See the Profile for ErikClick Here to Email ErikSend a Private Message to ErikDirect Link to This Post
 
quote
Originally posted by Rodney:

The Getrag, Isuzu and Muncie rear brackets all look the same but do not interchange.

What is different about the rear one? It will bolt right up to the Getrag. Is it shorter length , different angle???

IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery | Ogre's Cave
Real-Time Chat | Fiero Related Auctions on eBay



Copyright (c) 1999, C. Pennock