Pennock's Fiero Forum
  Technical Discussion & Questions - Archive
  3.4L DOHC-need a Bracket I'd

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Email This Page to Someone! | Printable Version


3.4L DOHC-need a Bracket I'd by RUNDLC
Started on: 10-23-2007 04:27 PM
Replies: 4
Last post by: RUNDLC on 10-23-2007 05:30 PM
RUNDLC
Member
Posts: 802
From: Elk Grove, California
Registered: Jul 2005


Feedback score: (2)
Leave feedback

Rate this member

Report this Post10-23-2007 04:27 PM Click Here to See the Profile for RUNDLCClick Here to Email RUNDLCSend a Private Message to RUNDLCDirect Link to This Post
Can someone ID this motor bracket for me please?


http://s222.photobucket.com...Test_Assembly4th.jpg
I need one of these brackets ASAP

Thanks
IP: Logged
PFF
System Bot
Erik
Member
Posts: 5616
From: Des Moines, Iowa
Registered: Jul 2002


Feedback score: (3)
Leave feedback





Total ratings: 169
Rate this member

Report this Post10-23-2007 04:46 PM Click Here to See the Profile for ErikClick Here to Email ErikSend a Private Message to ErikDirect Link to This Post
..goes below the ac compressor ..its a motor mount..I thought I sent that to you

[This message has been edited by Erik (edited 10-23-2007).]

IP: Logged
RUNDLC
Member
Posts: 802
From: Elk Grove, California
Registered: Jul 2005


Feedback score: (2)
Leave feedback

Rate this member

Report this Post10-23-2007 05:10 PM Click Here to See the Profile for RUNDLCClick Here to Email RUNDLCSend a Private Message to RUNDLCDirect Link to This Post
Erik, thats the one I am looking for but it didn't get here it's cool though. Do you have it? if so maybe you can put it with the harness & solenoid.

BTW the guy I was supposed to get the air injection pump flaked on me back to the internet!


RUNDLC
IP: Logged
Erik
Member
Posts: 5616
From: Des Moines, Iowa
Registered: Jul 2002


Feedback score: (3)
Leave feedback





Total ratings: 169
Rate this member

Report this Post10-23-2007 05:17 PM Click Here to See the Profile for ErikClick Here to Email ErikSend a Private Message to ErikDirect Link to This Post
ok now I am confused..what bracket did I send you then?? I removed that very bracket from a spare engine and it had the stock motor mount that I also sent you that you inquired about.
IP: Logged
RUNDLC
Member
Posts: 802
From: Elk Grove, California
Registered: Jul 2005


Feedback score: (2)
Leave feedback

Rate this member

Report this Post10-23-2007 05:30 PM Click Here to See the Profile for RUNDLCClick Here to Email RUNDLCSend a Private Message to RUNDLCDirect Link to This Post
I think you sent the actual mount part, but not the engine bracket

either that or I have lost a few marbles (maybe) I accused a teller of shorting me some cash this morning LOL, LOL (I was wrong)
I guess what caught my eye was there was no bolt holes that faced the front of the block.

I was gonna post a pic but may as well ask here, do you have the water pump housing dealy, that the stock oil cooler line runs too?
I can post a pic if I confused you again.

RUNDLC
IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery | Ogre's Cave
Real-Time Chat | Fiero Related Auctions on eBay



Copyright (c) 1999, C. Pennock