|
Dot Matrix Bezel (Page 1/1) |
|
liv4God
|
MAY 31, 05:46 AM
|
|
I recently got another Formula that had been picked apart some before I got it. I have a lot of what is missing, but one thing I don't have are the dot matrix bezels around the HVAC and auxiliary gauge pod. Hoping someone has these lying around!
Thanks 🙏
|
|
|
liv4God
|
JUN 03, 02:30 PM
|
|
Bump! I'm hoping to keep this car close to stock so these parts are important!
|
|
|
hercimer01
|
JUN 04, 12:27 AM
|
|
|
|
hercimer01
|
JUN 06, 01:58 AM
|
|
Hes still looking. Mine are pretty rough.
|
|
|
Tha Driver
|
JUN 06, 06:54 PM
|
|
I have a REALLY nice automatic set; I'll take $150 shipped for them. Only thing I see wrong is the two bottom holes for the screws on the radio surround is broken out on the bottom. Epoxy a small washer on the back & you're good to go. ~ Paul aka "Tha Driver"
Custom Fiberglass Parts
|
|
|
liv4God
|
JUN 07, 03:54 AM
|
|
quote | Originally posted by Tha Driver:
I have a REALLY nice automatic set; I'll take $150 shipped for them. Only thing I see wrong is the two bottom holes for the screws on the radio surround is broken out on the bottom. Epoxy a small washer on the back & you're good to go. ~ Paul aka "Tha Driver"
Custom Fiberglass Parts |
|
Could you send me some pictures? Also, I just need the piece around the aux gauge pod and the one around the radio/hvac so I don't need the whole set if you are willing to break it up.
On another note, just looked at your Fiberglass site, the 1/4 panel angel scoop looks awesome, is it ready for production?
|
|
|
smartaxel
|
JUN 08, 11:46 PM
|
|
I could use the 88 Auto shifter trim piece if you want to split I up. [This message has been edited by smartaxel (edited 06-08-2020).]
|
|
|
Tha Driver
|
JUN 09, 11:33 PM
|
|
quote | Originally posted by liv4God:
Could you send me some pictures? Also, I just need the piece around the aux gauge pod and the one around the radio/hvac so I don't need the whole set if you are willing to break it up.
On another note, just looked at your Fiberglass site, the 1/4 panel angel scoop looks awesome, is it ready for production? |
|
Just emailed you pics of the dot matrix pieces. You can post them here if you like. Don't really want to break up the set. Full 1/4's won't be available anytime soon because: 1) Lack of time & money, & 2) They're going to be a PITA to make with all the sharp edges & corners, & therefore are going to cost about twice what others charge for them, & I don't think folks will pay that for them. ~ Paul aka "Tha Driver"
Custom Fiberglass Parts
|
|
|
liv4God
|
JUN 11, 06:44 AM
|
|
quote | Originally posted by Tha Driver:
Just emailed you pics of the dot matrix pieces. You can post them here if you like. Don't really want to break up the set. Full 1/4's won't be available anytime soon because: 1) Lack of time & money, & 2) They're going to be a PITA to make with all the sharp edges & corners, & therefore are going to cost about twice what others charge for them, & I don't think folks will pay that for them. ~ Paul aka "Tha Driver"
Custom Fiberglass Parts |
|
I did not receive your email. I'll pm you my personal email.
I understand about the quarter panels, sure looks like a nice design though.
|
|
|