|
LHU Ecotec cradle mounts - obtaining / fabricating / welding (Page 1/2) |
|
SteveMushynsky
|
NOV 20, 07:47 PM
|
|
|
|
pmbrunelle
|
NOV 20, 08:38 PM
|
|
I'd suggest that most of your weldments be bolted onto the spaceframe / cradle of your Fiero.
As your skills develop, it will then be possible to remove and remake the beginner-grade horrors you did.
Start with the simpler weldments if you can; get scrap to simulate the parts to be welded, do a practice run, then go work on the real parts.
Doing endless practise parts is pointless; at least for me, I am most motivated to learn and do well when I'm working on the real McCoy.
|
|
|
SteveMushynsky
|
NOV 21, 01:14 AM
|
|
quote | Originally posted by pmbrunelle: I'd suggest that most of your weldments be bolted onto the spaceframe / cradle of your Fiero. ...
|
|
I like that. It sounds like good advice.------------------ Steve Mushynsky
1984 Fiero 2M4 34K miles
1986 Fiero SE I4 (donor now) Lots of good miles. One very bad mile.
1987 Fiero Tried to kill me (gone to a 'better place') Prior owner failed to tighten a bolt. Trailing arm separated at 70 mph
|
|
|
Dennis LaGrua
|
NOV 22, 02:05 PM
|
|
I do not believe that this version of the Ecotec has been successfully installed in a Fiero so far. The engine features direct injection, VVT, and drive by wire. You can be successful mounting it but the PCM control and engine management aspects may be an issue. ------------------ " THE BLACK PARALYZER" -87GT 3800SC Series III engine, custom ZZP /Frozen Boost Intercooler setup, 3.4" Pulley, Northstar TB, LS1 MAF, 3" Spintech/Hedman Exhaust, P-log Manifold, Autolite 104's, MSD wires, Custom CAI, 4T65eHD w. custom axles, Champion Radiator, S10 Brake Booster, HP Tuners VCM Suite. "THE COLUSSUS" 87GT - ALL OUT 3.4L Turbocharged engine, Garrett Hybrid Turbo, MSD ign., modified TH125H " ON THE LOOSE WITHOUT THE JUICE "
|
|
|
SteveMushynsky
|
NOV 23, 05:19 AM
|
|
quote | Originally posted by Dennis LaGrua: ... but the PCM control and engine management aspects may be an issue.
|
|
Thank you, Dennis.
LHU uses the E39 (2012) or E39A (2013) ECU in the Buick Regal GS.
I have read a GM recall notice that the E39 had some manner of 'issue' and that parts sale of replacement E39's may have been "frozen" at for some time, reason unknown. On the other hand, I've read that some have pulled their E39A's in favor of using an E39. Apparently this was due to some tuning issues. I understand that this was during the time that GM was transitioning to a torque-demand basis in their powertrain controls. Perhaps this was involved in the recall notice and/or there were learning curve issues on the part of tune modifiers? I understand that tunes have been accomplished on the E39 / E39A and are available for use with the Regals, at least.
In any case, my understanding is that if I can obtain a complete set of ECU, BCM, harness, DBW pedal, instrument cluster, possibly ignition relay, etc from one 2012 0r 2013 Buick Regal GS in its entirety, I should be able to get up & running without additional tuning initially necessary as I won't be doing engine modifications at first. Hopefully, I can deal with tuning afterward to optimize the engine in a Fiero installation.
Might anyone have any advice on this scenario?
------------------ Steve Mushynsky
1984 Fiero 2M4 34K miles
1986 Fiero SE I4 (donor now) Lots of good miles. One very bad mile.
1987 Fiero Tried to kill me (gone to a 'better place') Prior owner failed to tighten a bolt. Trailing arm separated at 70 mph
|
|
|
wftb
|
NOV 23, 08:35 AM
|
|
I was lucky enough to find a wreckers that was willing to give me the entire wiring harness with the ecm bcm and the steering column with the key in it. This allowed me to get the car running initially and then later I added the donor car fuel pump and instrument cluster. HP tuners came later so I could get rid of the ignition switch I had in the glove box. Drive by wire just means you need the pedal assembly. DI controls will be in your harness etc and the high pressure pump is mounted on the engine. It has all been done before just not in a Fiero.
------------------ 86 GT built 2.2 ecotec turbo rear SLA suspension QA1 coilovers on tube arms[This message has been edited by wftb (edited 11-23-2019).]
|
|
|
Dennis LaGrua
|
NOV 23, 10:34 AM
|
|
quote | Originally posted by SteveMushynsky:
Thank you, Dennis.
LHU uses the E39 (2012) or E39A (2013) ECU in the Buick Regal GS.
I have read a GM recall notice that the E39 had some manner of 'issue' and that parts sale of replacement E39's may have been "frozen" at for some time, reason unknown. On the other hand, I've read that some have pulled their E39A's in favor of using an E39. Apparently this was due to some tuning issues. I understand that this was during the time that GM was transitioning to a torque-demand basis in their powertrain controls. Perhaps this was involved in the recall notice and/or there were learning curve issues on the part of tune modifiers? I understand that tunes have been accomplished on the E39 / E39A and are available for use with the Regals, at least.
In any case, my understanding is that if I can obtain a complete set of ECU, BCM, harness, DBW pedal, instrument cluster, possibly ignition relay, etc from one 2012 0r 2013 Buick Regal GS in its entirety, I should be able to get up & running without additional tuning initially necessary as I won't be doing engine modifications at first. Hopefully, I can deal with tuning afterward to optimize the engine in a Fiero installation.
Might anyone have any advice on this scenario?
|
|
Sounds like you are on the right track as that PCM is expecting many of the inputs from the devices that you named. ------------------ " THE BLACK PARALYZER" -87GT 3800SC Series III engine, custom ZZP /Frozen Boost Intercooler setup, 3.4" Pulley, Northstar TB, LS1 MAF, 3" Spintech/Hedman Exhaust, P-log Manifold, Autolite 104's, MSD wires, Custom CAI, 4T65eHD w. custom axles, Champion Radiator, S10 Brake Booster, HP Tuners VCM Suite. "THE COLUSSUS" 87GT - ALL OUT 3.4L Turbocharged engine, Garrett Hybrid Turbo, MSD ign., modified TH125H " ON THE LOOSE WITHOUT THE JUICE "
|
|
|
SteveMushynsky
|
NOV 23, 06:37 PM
|
|
quote | Originally posted by wftb: ... It has all been done before just not in a Fiero.
|
|
Thanks, wtfb.
That's what I've read and hope to do, yes.
------------------ Steve Mushynsky
1984 Fiero 2M4 34K miles
1986 Fiero SE I4 (donor now) Lots of good miles. One very bad mile.
1987 Fiero Tried to kill me (gone to a 'better place') Prior owner failed to tighten a bolt. Trailing arm separated at 70 mph
|
|
|
SteveMushynsky
|
NOV 23, 06:40 PM
|
|
quote | Originally posted by Dennis LaGrua: ... Sounds like you are on the right track as that PCM is expecting many of the inputs from the devices that you named.
|
|
Thank you, Dennis.
Am I missing anything I need to include or pay attention to?
------------------ Steve Mushynsky
1984 Fiero 2M4 34K miles
1986 Fiero SE I4 (donor now) Lots of good miles. One very bad mile.
1987 Fiero Tried to kill me (gone to a 'better place') Prior owner failed to tighten a bolt. Trailing arm separated at 70 mph
|
|
|
wftb
|
NOV 25, 09:39 AM
|
|
|
|
|